Stm32怎么用串口中断方式接收发送
时间: 2023-08-09 18:10:11 浏览: 31
在使用STM32的串口中断方式接收发送时,需要先设置串口的工作模式为中断模式。然后在代码中编写中断处理程序来处理接收和发送数据。
以下是一个简单的使用USART1的接收发送代码:
```c
#include "stm32f10x.h"
void USART1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
// 打开USART1和GPIOA的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
// 配置GPIOA.9为USART1的Tx引脚和GPIOA.10为USART1的Rx引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置USART1
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 配置USART1的中断
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
// 打开USART1的接收中断
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
// 启动USART1
USART_Cmd(USART1, ENABLE);
}
void USART1_IRQHandler(void)
{
if (USART_GetITStatus(USART1, USART_IT_RXNE) != RESET) // 接收数据中断
{
uint8_t data = USART_ReceiveData(USART1); // 读取接收到的数据
// 处理接收到的数据
}
if (USART_GetITStatus(USART1, USART_IT_TXE) != RESET) // 发送数据中断
{
// 发送数据
USART_SendData(USART1, data);
}
}
int main(void)
{
USART1_Init();
while (1)
{
// 主循环中进行其他操作
}
}
```
在上面的代码中,我们首先初始化了USART1的GPIO和USART模块,并设置了接收中断和发送中断。在USART1的中断处理程序中,我们可以通过读取USART1的寄存器来获取接收到的数据,并通过USART1的发送寄存器将数据发送出去。在主循环中,我们可以进行其他操作,因为USART1的中断会自动处理接收和发送数据。