Rt thread 如何实现一个GPIO口 控制led灯的亮度 要求不能使用pwm 且不阻塞
时间: 2024-02-22 19:55:04 浏览: 14
如果不能使用 PWM,那么可以通过修改 GPIO 的输出频率来控制 LED 的亮度,这个方法也称为软件 PWM。
在 RT-Thread 中,可以使用硬件定时器和 GPIO 驱动来实现软件 PWM。具体步骤如下:
1. 在设备树中定义 GPIO 和定时器设备节点。
```
led {
compatible = "gpio-leds";
green {
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
label = "Green LED";
};
};
pwm-timer {
compatible = "rtthread,pwm-timer";
#pwm-cells = <3>;
};
```
其中,`gpio-leds` 是 GPIO 驱动的一个子驱动,用于控制 LED 灯的状态;`rtthread,pwm-timer` 是定时器驱动的一个子驱动,用于控制 PWM 的输出频率。
2. 在应用程序中打开 GPIO 设备和定时器设备,并启动 PWM。
```
#include <rtthread.h>
#include <rtdevice.h>
static rt_device_t led_device;
static rt_device_t pwm_device;
static void led_pwm_thread_entry(void *parameter)
{
rt_uint32_t count = 0;
rt_uint32_t period = 100; /* PWM 周期为 100ms */
rt_uint32_t duty_cycle = 50; /* PWM 占空比为 50% */
rt_device_open(led_device, RT_DEVICE_FLAG_WRONLY); /* 打开 GPIO 设备 */
rt_device_open(pwm_device, RT_DEVICE_FLAG_WRONLY); /* 打开定时器设备 */
while (1)
{
count++;
if (count % period < duty_cycle)
{
rt_device_write(led_device, 0, &RT_TRUE, 1); /* 设置 GPIO 输出高电平 */
}
else
{
rt_device_write(led_device, 0, &RT_FALSE, 1); /* 设置 GPIO 输出低电平 */
}
rt_thread_mdelay(1); /* 延时 1ms */
/* 启动 PWM */
rt_device_control(pwm_device, PWM_CMD_START, &period);
}
}
int led_pwm_init(void)
{
led_device = rt_device_find("led0");
pwm_device = rt_device_find("timer3");
if (led_device == RT_NULL || pwm_device == RT_NULL)
{
rt_kprintf("failed to find devices\n");
return -1;
}
rt_thread_t thread = rt_thread_create("led_pwm", led_pwm_thread_entry, RT_NULL, 1024, 20, 10);
if (thread != RT_NULL)
{
rt_thread_startup(thread);
}
return 0;
}
```
在这个例子中,我们使用了一个线程来控制 LED 的亮度,每隔 1ms 更新一次 GPIO 的输出状态,并启动定时器来产生 PWM 信号。
需要注意的是,定时器的周期应该是 PWM 周期的整数倍,否则 PWM 的输出频率会有误差。
3. 修改定时器设备驱动来实现 PWM 的输出。
```
#include <rtdevice.h>
#include <rtthread.h>
#define PWM_CMD_START RT_PWM_CMD_MAX
#define PWM_CMD_STOP (RT_PWM_CMD_MAX + 1)
static rt_uint32_t period;
static rt_err_t pwm_timer_control(rt_device_t dev, int cmd, void *args)
{
switch (cmd)
{
case PWM_CMD_START:
period = *(rt_uint32_t *)args;
TIM3->ARR = period - 1; /* 设置定时器周期 */
TIM3->PSC = SystemCoreClock / (period * 1000) - 1; /* 设置定时器分频 */
TIM3->CCR1 = period / 2 - 1; /* 设置 PWM 占空比 */
TIM3->CCER |= TIM_CCER_CC1E; /* 启用定时器比较输出通道 */
TIM3->CR1 |= TIM_CR1_CEN; /* 启动定时器 */
break;
case PWM_CMD_STOP:
TIM3->CR1 &= ~TIM_CR1_CEN; /* 停止定时器 */
break;
default:
return -RT_ENOSYS;
}
return RT_EOK;
}
static struct rt_device pwm_timer_device =
{
.type = RT_Device_Class_Timer,
.init = RT_NULL,
.open = RT_NULL,
.close = RT_NULL,
.read = RT_NULL,
.write = RT_NULL,
.control = pwm_timer_control,
.user_data = RT_NULL,
};
int rt_hw_pwm_init(void)
{
rt_device_register(&pwm_timer_device, "timer3", RT_DEVICE_FLAG_WRONLY);
return 0;
}
```
在这个例子中,我们添加了两个自定义的命令 `PWM_CMD_START` 和 `PWM_CMD_STOP`,用于启动和停止 PWM 输出。在启动 PWM 时,我们需要根据 PWM 周期计算定时器的分频和周期,并设置定时器的比较输出通道和 PWM 占空比。在停止 PWM 时,我们需要停止定时器的计数。
需要注意的是,这个例子只是一个简单的实现,实际使用中需要考虑更多的细节和异常情况。例如,需要对定时器的分频进行限制,以防止分频过大或过小导致 PWM 输出频率不准确;需要处理定时器溢出的情况,以防止 PWM 输出异常等。