PD3.0协议如何发送Control Message
时间: 2024-04-28 07:22:27 浏览: 14
PD3.0协议发送Control Message需要进行以下步骤:
1. 在USB Type-C连接器上检测到插入事件后,启动Vbus电压上升,进入握手过程。
2. 在握手过程中,双方交换协商信息,确认连接的协议版本等信息。
3. 在确认连接的协议版本为PD3.0后,双方可以通过发送Control Message来交换更多的信息。
4. 发送Control Message时,需要使用Message ID来标识不同类型的Message,并在Message中包含必要的参数。
5. 接收方收到Control Message后,会根据Message ID和参数执行相应的操作。
总之,PD3.0协议发送Control Message需要进行握手过程,并通过Message ID和参数标识和传递信息。
相关问题
PD3.0协议发送Control Message的具体代码
以下是PD3.0协议发送Control Message的具体代码,仅供参考:
```c
// 准备Control Message的数据包
uint16_t header = 0x0000; // Message Header
uint16_t extHeader = 0x0000; // Extended Message Header
uint16_t ctrlMsgData = 0x0000; // Control Message Data
uint16_t crc = 0x0000; // CRC
// 在Source Caps中寻找匹配的PDO
for (int i = 0; i < numSourceCaps; i++) {
if (sourceCaps[i].fixedSupply && sourceCaps[i].voltage == sinkVoltage && sourceCaps[i].maxCurrent >= sinkMaxCurrent) {
// 匹配的PDO一般包含了Sink需要的电源参数信息
ctrlMsgData = sourceCaps[i].rawData;
break;
}
}
// 向Sink发送SOP消息
sendSOP();
// 发送Control Message数据包
sendData(header, extHeader, ctrlMsgData, crc);
// 接收Sink发送的GoodCRC消息作为确认
receiveGoodCRC();
```
需要注意的是,具体实现代码中的`sendSOP()`、`sendData()`和`receiveGoodCRC()`函数需要根据具体的硬件平台和实现方式进行编写。在实现代码时,需要遵守PD3.0协议中的相关规范,确保Control Message的可靠传输。
PD3.0协议发送Control Message的代码实现
以下是使用C语言实现PD3.0协议发送Control Message的代码示例:
```c
// 定义Control Message结构体
typedef struct {
uint16_t header; // Control Message头部
uint16_t length; // Control Message长度
uint16_t id; // Control Message ID
uint16_t data[7]; // Control Message数据
} pd_ctrl_msg_t;
// 发送Control Message函数
void send_ctrl_msg(uint16_t id, uint16_t* data, uint8_t data_len) {
pd_ctrl_msg_t ctrl_msg;
ctrl_msg.header = PD_CTRL_MSG_HEADER;
ctrl_msg.length = PD_CTRL_MSG_LENGTH(data_len);
ctrl_msg.id = id;
memcpy(ctrl_msg.data, data, data_len * sizeof(uint16_t));
uint16_t crc = calculate_crc((uint8_t*)&ctrl_msg, ctrl_msg.length + PD_CTRL_MSG_HEADER_SIZE);
// 将Control Message数据发送到PD设备
pd_send_data((uint8_t*)&ctrl_msg, ctrl_msg.length + PD_CTRL_MSG_HEADER_SIZE, crc);
}
```
其中,`PD_CTRL_MSG_HEADER`和`PD_CTRL_MSG_LENGTH`是PD3.0协议中定义的Control Message头部和长度计算宏。`calculate_crc`函数是计算Control Message CRC校验值的函数。`pd_send_data`函数是将Control Message数据发送到PD设备的函数。在使用此代码时,需要根据实际情况实现这些函数。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)