帮我写一个stm32f103流水灯程序
时间: 2023-12-07 07:02:57 浏览: 55
好的,下面是一个使用STM32F103单片机的流水灯程序:
```
#include "stm32f10x.h"
void delay(unsigned long ms)
{
unsigned long i, j;
for (i = 0; i < ms; i++)
for (j = 0; j < 7200; j++);
}
int main(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructure);
while (1)
{
GPIO_SetBits(GPIOB, GPIO_Pin_5);
delay(1000);
GPIO_ResetBits(GPIOB, GPIO_Pin_5);
delay(1000);
}
}
```
请注意,这是一个简单的示例代码,可能需要根据您的硬件环境和需求进行调整。
相关问题
写一个控制STM32F103流水灯代码c语言
以下是一个简单的控制STM32F103流水灯的C语言代码示例:
```c
#include "stm32f10x.h"
// 延时函数
void delay(uint32_t count) {
for (uint32_t i = 0; i < count; i++) {
for (uint32_t j = 0; j < 7200; j++) {
// 空操作,用于增加延时时间
}
}
}
int main(void) {
// 初始化GPIO
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13 | GPIO_Pin_14 | GPIO_Pin_15;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOC, &GPIO_InitStructure);
while (1) {
// 点亮LED1,熄灭LED2和LED3
GPIO_SetBits(GPIOC, GPIO_Pin_13);
GPIO_ResetBits(GPIOC, GPIO_Pin_14 | GPIO_Pin_15);
delay(500000);
// 熄灭LED1,点亮LED2,熄灭LED3
GPIO_ResetBits(GPIOC, GPIO_Pin_13 | GPIO_Pin_15);
GPIO_SetBits(GPIOC, GPIO_Pin_14);
delay(500000);
// 熄灭LED1和LED2,点亮LED3
GPIO_ResetBits(GPIOC, GPIO_Pin_13 | GPIO_Pin_14);
GPIO_SetBits(GPIOC, GPIO_Pin_15);
delay(500000);
}
}
```
这段代码使用了STM32F10x标准库来控制GPIO口,通过循环实现LED灯的流水效果。请注意,具体的引脚定义和时钟配置可能需要根据你的硬件平台进行调整。
用stm32cubeide写一个stm32F103c8T6流水灯程序
好的,以下是使用STM32CubeIDE编写STM32F103C8T6流水灯程序的步骤:
1. 打开STM32CubeIDE并创建一个新的STM32项目,选择STM32F103C8Tx芯片作为目标芯片。
2. 在"Project Manager"中右键单击"src"文件夹并选择"New > C File",创建一个名为"main.c"的文件。
3. 在main.c中添加以下代码:
```
#include "stm32f1xx.h"
int main(void)
{
RCC->APB2ENR |= 0x00000004; // Enable GPIOC clock
GPIOC->CRH &= 0xFF0FFFFF; // Configure PC8-PC11 as outputs
GPIOC->CRH |= 0x00300000;
while (1)
{
GPIOC->BSRR = 0x00000F00; // Turn on LEDs
for (int i = 0; i < 1000000; i++); // Delay
GPIOC->BSRR = 0x00F00000; // Turn off LEDs
for (int i = 0; i < 1000000; i++); // Delay
}
}
```
4. 在"Project Manager"中右键单击"Drivers"文件夹并选择"New > C File",创建一个名为"stm32f1xx_it.c"的文件。
5. 在"Project Manager"中右键单击"Drivers"文件夹并选择"New > C File",创建一个名为"stm32f1xx_hal_msp.c"的文件。
6. 在"Project Manager"中右键单击"Src"文件夹并选择"New > C++ File",创建一个名为"stm32f1xx_hal_conf.h"的文件。
7. 在"stm32f1xx_hal_conf.h"文件中添加以下代码:
```
#ifndef __STM32F1xx_HAL_CONF_H
#define __STM32F1xx_HAL_CONF_H
#include "stm32f1xx.h"
#define HAL_RCC_MODULE_ENABLED // Enable RCC HAL module
#define HAL_GPIO_MODULE_ENABLED // Enable GPIO HAL module
#endif /* __STM32F1xx_HAL_CONF_H */
```
8. 在"Project Manager"中右键单击"Drivers > STM32F1xx_HAL_Driver > Inc"文件夹并选择"New > C++ File",创建一个名为"stm32f1xx_hal_conf.h"的文件。
9. 在"stm32f1xx_hal_conf.h"文件中添加以下代码:
```
#ifndef __STM32F1xx_HAL_CONF_H
#define __STM32F1xx_HAL_CONF_H
#include "stm32f1xx.h"
#define HAL_RCC_MODULE_ENABLED // Enable RCC HAL module
#define HAL_GPIO_MODULE_ENABLED // Enable GPIO HAL module
#endif /* __STM32F1xx_HAL_CONF_H */
```
10. 在"Project Manager"中右键单击"Drivers > STM32F1xx_HAL_Driver > Src"文件夹并选择"New > C File",创建一个名为"stm32f1xx_hal_msp.c"的文件。
11. 在"Project Manager"中右键单击"Drivers > STM32F1xx_HAL_Driver > Src"文件夹并选择"New > C File",创建一个名为"stm32f1xx_it.c"的文件。
12. 在"stm32f1xx_it.c"文件中添加以下代码:
```
#include "stm32f1xx_hal.h"
void SysTick_Handler(void)
{
HAL_IncTick();
}
void EXTI0_IRQHandler(void)
{
HAL_GPIO_EXTI_IRQHandler(GPIO_PIN_0);
}
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
{
// TODO: Add your code here
}
```
13. 在"stm32f1xx_hal_msp.c"文件中添加以下代码:
```
#include "stm32f1xx_hal.h"
void HAL_MspInit(void)
{
__HAL_RCC_AFIO_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
}
void HAL_TIM_Base_MspInit(TIM_HandleTypeDef *htim)
{
__HAL_RCC_TIM3_CLK_ENABLE();
}
void HAL_UART_MspInit(UART_HandleTypeDef *huart)
{
__HAL_RCC_USART1_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
GPIO_InitTypeDef GPIO_InitStruct = {0};
GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}
void HAL_UART_MspDeInit(UART_HandleTypeDef *huart)
{
__HAL_RCC_USART1_FORCE_RESET();
__HAL_RCC_USART1_RELEASE_RESET();
HAL_GPIO_DeInit(GPIOA, GPIO_PIN_9 | GPIO_PIN_10);
}
```
14. 将STM32F103C8T6开发板连接到计算机上,并在STM32CubeIDE中选择正确的调试和编程配置。
15. 编译并烧录程序到开发板上,即可看到流水灯效果。
希望这些步骤能够帮助到你。