写一个读写芯片hym8563时钟芯片的完整代码，用stm32f407最好使用hal库

以下是一个基于STM32F407芯片，使用HAL库进行读写HYM8563时钟芯片的完整代码示例：

#include "stm32f4xx_hal.h"
#include "stdio.h"

#define HYM8563_ADDRESS 0x51 // HYM8563 I2C地址
#define I2C_TIMEOUT 100 // I2C读写超时时间

I2C_HandleTypeDef hi2c1;

void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_I2C1_Init(void);

void setTime(int hour, int minute, int second);
void readTime(int* hour, int* minute, int* second);

int main(void) {
  HAL_Init();
  SystemClock_Config();
  MX_GPIO_Init();
  MX_I2C1_Init();
  
  int hour = 0, minute = 0, second = 0;
  setTime(0, 0, 0); // 初始化时间为0点0分0秒
  
  while (1) {
    readTime(&hour, &minute, &second); // 读取当前时间
    printf("Current time: %d:%d:%d\r\n", hour, minute, second);
    HAL_Delay(1000); // 每秒更新一次时间
  }
}

void setTime(int hour, int minute, int second) {
  uint8_t setTimeData[4] = {0};
  setTimeData[0] = second;
  setTimeData[1] = minute;
  setTimeData[2] = hour;
  
  HAL_I2C_Mem_Write(&hi2c1, HYM8563_ADDRESS, 0, I2C_MEMADD_SIZE_8BIT, setTimeData, 3, I2C_TIMEOUT);
}

void readTime(int* hour, int* minute, int* second) {
  uint8_t readTimeData[3] = {0};
  HAL_I2C_Mem_Read(&hi2c1, HYM8563_ADDRESS, 0, I2C_MEMADD_SIZE_8BIT, readTimeData, 3, I2C_TIMEOUT);
  
  *second = readTimeData[0];
  *minute = readTimeData[1];
  *hour = readTimeData[2];
}

void SystemClock_Config(void) {
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  __HAL_RCC_PWR_CLK_ENABLE();
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
  RCC_OscInitStruct.PLL.PLLM = 8;
  RCC_OscInitStruct.PLL.PLLN = 192;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
  RCC_OscInitStruct.PLL.PLLQ = 4;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
    Error_Handler();
  }

  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
    Error_Handler();
  }
}

static void MX_I2C1_Init(void) {
  hi2c1.Instance = I2C1;
  hi2c1.Init.ClockSpeed = 100000;
  hi2c1.Init.DutyCycle = I2C_DUTYCYCLE_2;
  hi2c1.Init.OwnAddress1 = 0;
  hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
  hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  hi2c1.Init.OwnAddress2 = 0;
  hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
  if (HAL_I2C_Init(&hi2c1) != HAL_OK) {
    Error_Handler();
  }
}

static void MX_GPIO_Init(void) {
  __HAL_RCC_GPIOA_CLK_ENABLE();
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
  GPIO_InitStruct.Alternate = GPIO_AF4_I2C1;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}

void Error_Handler(void) {
  __disable_irq();
  while (1) {
  }
}

该代码使用HAL库进行I2C通信，通过setTime函数设置时间，通过readTime函数读取时间。在main函数中，每秒更新一次时间并通过printf函数打印到串口上。在使用该代码时，需要先连接HYM8563时钟芯片到STM32F407的I2C总线上，并将I2C1的SCL引脚连接到PA9，SDA引脚连接到PA10上。