没有合适的资源?快使用搜索试试~ 我知道了~
首页MIL-STD-1553B协议标准
MIL-STD-1553B协议标准
5星 · 超过95%的资源 需积分: 43 73 下载量 21 浏览量
更新于2023-03-16
收藏 442KB PDF 举报
美国国防部指定的时分命令/响应多路复用数据总线,在国内外的军用电子环境得到广泛使用
资源详情
资源推荐
THIS IS NOT THE ORIGINAL WORD PROCESSOR FILE. IT IS THE SAME AS THE ORIGINAL,
EXCEPT FOR SOME FORMATTING. NOTICES 1 THROUGH 4 ARE INCORPORATED.
INCH-POUND
NOTE: Notice 4, dated 15 January 1996, changes the
cover page of this standard for administrative reasons.
There are no other changes to this document.
MIL-STD-1553B
21 SEPTEMBER 1978
SUPERSEDING
MIL-STD-1553A
30 APRIL 1975
DEPARTMENT OF DEFENSE
INTERFACE STANDARD
FOR
DIGITAL TIME DIVISION COMMAND/RESPONSE
MULTIPLEX DATA BUS
A
MSC N/A
AREA MCCR
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
MIL-STD-1553B
with notice 1, 2, 3, and 4.
RETYPED VERSION
Supersedes cover page of MIL-STD-1553B, dated 21 September 1978
ii
MIL-STD-1553B
with notice 1, 2, 3, and 4.
RETYPED VERSION
DEPARTMENT OF DEFENSE
Washington DC 20360
DIGITAL TIME DIVISION COMMAND/RESPONSE MULTIPLEX DATA BUS
1. This standard is approved for use by all Departments and Agencies of the Department of
Defense.
2. Beneficial comments (recommendations, additions, deletions) and any pertinent data which
may be of use in improving this document should be addressed to: ASC/ENSI, Bldg 125, 2335
Seventh Street, Suite 6, Wright-Patterson AFB OH 45433-7809 by using the Standardization
Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by
letter. NEW ADDRESS, 1996: ASC/ENSI, 2530 LOOP ROAD WEST, WRIGHT
PATTERSON AFB, OH 45433-7101
Supersedes page ii of MIL-STD-1553B, dated 21 September 1978.
iii
MIL-STD-1553B
with notice 1, 2, 3, and 4.
RETYPED VERSION
FOREWORD
This standard contains requirements for a digital time division command/response multiplex data bus for
use in systems integration. Even with the use of this standard, differences may exist between multiplex
data buses in different system applications due to particular application requirements and the designer
options allowed in this standard. The system designer must recognize this fact and design the multiplex
bus controller hardware and software to accommodate such differences. These designer selected options
must exist to allow the necessary flexibility in the design of specific multiplex systems in order to provide
for the control mechanism, architectural redundancy, degradation concept and traffic patterns peculiar to
the specific application requirements. Appendix, Section 30 selects those options which shall be required
and further restricts certain portions of the standard for the use in all dual standby redundant applications
for the Army, Navy, and Air Force.
Supersedes page iii dated 12 February 1980.
iv
MIL-STD-1553B
with notice 1, 2, 3, and 4.
RETYPED VERSION
CONTENTS
Paragraph Page
1. SCOPE 1
1.1 Scope 1
1.2 Application. 1
2. REFERENCED DOCUMENTS 1
2.1 Issue of document 1
3. DEFINITIONS 1
3.1 Bit 1
3.2 Bit rate 1
3.3 Pulse code modulation (PCM) 1
3.4 Time division multiplexing (TDM) 1
3.5 Half duplex 1
3.6 Word 1
3.7 Message 3
3.8 Subsystem 3
3.9 Data bus 3
3.10 Terminal 3
*3.11 Bus controller (BC) 3
*3.12 Bus monitor (BM) 3
3.13 Remote terminal (RT) 3
3.14 Asynchronous operation 3
3.15 Dynamic bus control 3
3.16 Command/Response 3
3.17 Redundant data bus 3
3.18 Broadcast 3
3.19 Mode code 3
4. GENERAL REQUIREMENTS 4
4.1 Test and operating requirements 4
4.2 Data bus operation 4
4.3 Characteristics 4
4.3.1 Data form 4
4.3.2 Bit priority 4
4.3.3 Transmission method 4
4.3.3.1 Modulation 4
4.3.3.2 Data code 4
4.3.3.3 Transmission bit rate 4
4.3.3.4 Word size 4
4.3.3.5 Word formats 4
4.3.3.5.1 Command word 8
4.3.3.5.1.1 Sync 8
4.3.3.5.1.2 Remote terminal address 8
4.3.3.5.1.3 Transmit/receive 8
4.3.3.5.1.4 Subaddress/mode 8
4.3.3.5.1.5 Data word count/mode code 8
4.3.3.5.1.6 Parity 8
4.3.3.5.1.7 Optional mode control 8
4.3.3.5.1.7.1 Dynamic bus control 9
Supersedes page iv dated 21 September 1978.
v
剩余50页未读,继续阅读
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功