keil5做温度传感器代码

下面是一个基于Keil5的温度传感器代码示例：

#include <stdio.h>
#include <stdint.h>
#include "stm32f4xx.h"

#define ADC1_DR_ADDRESS ((uint32_t)0x4001204C)

float temperature = 0.0f;

void ADC_Configuration(void);
void ADC1_IRQHandler(void);

int main(void)
{
    ADC_Configuration();

    while(1)
    {
        printf("Temperature: %.2f\n", temperature);
    }
}

void ADC_Configuration(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;
    ADC_CommonInitTypeDef ADC_CommonInitStructure;
    ADC_InitTypeDef ADC_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;

    // Enable GPIOA clock
    RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);

    // Configure ADC1_3 pin as analog input
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

    // Enable ADC1 clock
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);

    // ADC Common Init
    ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;
    ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
    ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled;
    ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
    ADC_CommonInit(&ADC_CommonInitStructure);

    // ADC1 Init
    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanConvMode = DISABLE;
    ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 1;
    ADC_Init(ADC1, &ADC_InitStructure);

    // Configure ADC1 channel3 interrupt
    NVIC_InitStructure.NVIC_IRQChannel = ADC_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    // Enable ADC1 channel3 interrupt
    ADC_ITConfig(ADC1, ADC_IT_EOC, ENABLE);

    // Enable ADC1
    ADC_Cmd(ADC1, ENABLE);

    // Start ADC1 Software Conversion
    ADC_SoftwareStartConv(ADC1);
}

void ADC1_IRQHandler(void)
{
    if(ADC_GetITStatus(ADC1, ADC_IT_EOC) != RESET)
    {
        // Calculate temperature
        uint16_t adc_value = ADC_GetConversionValue(ADC1);
        temperature = ((3.3f * adc_value / 4096.0f) - 0.76f) / 0.0025f + 25.0f;

        // Clear ADC1 EOC pending interrupt bit
        ADC_ClearITPendingBit(ADC1, ADC_IT_EOC);
    }
}

这个代码使用了STM32F4系列的单片机，采用了ADC模块来获取温度传感器的输出，并通过串口将温度值打印出来。你需要根据自己的硬件平台和具体传感器的接口来修改代码。