STM32的DHT11.H文件
时间: 2024-06-09 10:07:05 浏览: 7
以下是一个DHT11的头文件示例,可以在STM32上使用:
```c
#ifndef __DHT11_H
#define __DHT11_H
#include "stm32f4xx_hal.h"
//DHT11数据结构体
typedef struct {
uint8_t humidity_int; //湿度的整数部分
uint8_t humidity_dec; //湿度的小数部分
uint8_t temperature_int;//温度的整数部分
uint8_t temperature_dec;//温度的小数部分
} DHT11_Data_TypeDef;
//DHT11传感器初始化函数
void DHT11_Init(void);
//DHT11传感器读取数据函数
uint8_t DHT11_ReadData(DHT11_Data_TypeDef *DHT11_Data);
#endif /* __DHT11_H */
```
其中包含了DHT11数据结构体和初始化函数,以及读取数据的函数。需要注意的是,这里使用了HAL库来进行底层操作。如果你使用的是其他的库或者直接操作寄存器,需要相应地修改代码。
相关问题
stm32f103r6生成dht11.c和dht11.h文件
以下是基于STM32 HAL库的DHT11驱动代码示例:
dht11.h
```c
#ifndef __DHT11_H
#define __DHT11_H
#include "stm32f1xx_hal.h"
#define DHT11_PORT GPIOA
#define DHT11_PIN GPIO_PIN_0
void delay_us(uint32_t us);
void DHT11_Start(void);
uint8_t DHT11_Check(void);
uint8_t DHT11_Read_Bit(void);
uint8_t DHT11_Read_Byte(void);
uint8_t DHT11_Read_Data(uint8_t *humidity, uint8_t *temperature);
#endif
```
dht11.c
```c
#include "dht11.h"
void delay_us(uint32_t us)
{
uint32_t count = us * (SystemCoreClock / 1000000) / 5;
while(count--);
}
void DHT11_Start(void)
{
HAL_GPIO_WritePin(DHT11_PORT, DHT11_PIN, GPIO_PIN_RESET);
delay_us(18000);
HAL_GPIO_WritePin(DHT11_PORT, DHT11_PIN, GPIO_PIN_SET);
delay_us(20);
HAL_GPIO_WritePin(DHT11_PORT, DHT11_PIN, GPIO_PIN_RESET);
}
uint8_t DHT11_Check(void)
{
uint8_t response = 1;
uint16_t count = 0;
while(HAL_GPIO_ReadPin(DHT11_PORT, DHT11_PIN) == GPIO_PIN_SET)
{
count++;
if(count > 10000)
{
response = 0;
break;
}
}
return response;
}
uint8_t DHT11_Read_Bit(void)
{
uint8_t response = 1;
uint16_t count = 0;
while(HAL_GPIO_ReadPin(DHT11_PORT, DHT11_PIN) == GPIO_PIN_RESET)
{
count++;
if(count > 10000)
{
response = 0;
break;
}
}
delay_us(40);
if(HAL_GPIO_ReadPin(DHT11_PORT, DHT11_PIN) == GPIO_PIN_SET)
{
response = 1;
}
else
{
response = 0;
}
count = 0;
while(HAL_GPIO_ReadPin(DHT11_PORT, DHT11_PIN) == GPIO_PIN_SET)
{
count++;
if(count > 10000)
{
response = 0;
break;
}
}
return response;
}
uint8_t DHT11_Read_Byte(void)
{
uint8_t i, temp = 0;
for(i = 0; i < 8; i++)
{
temp |= (DHT11_Read_Bit() << (7 - i));
}
return temp;
}
uint8_t DHT11_Read_Data(uint8_t *humidity, uint8_t *temperature)
{
uint8_t response = 0;
uint8_t buffer[5];
DHT11_Start();
if(DHT11_Check() == 0)
{
response = 1;
buffer[0] = DHT11_Read_Byte();
buffer[1] = DHT11_Read_Byte();
buffer[2] = DHT11_Read_Byte();
buffer[3] = DHT11_Read_Byte();
buffer[4] = DHT11_Read_Byte();
if(buffer[4] == (buffer[0] + buffer[1] + buffer[2] + buffer[3]))
{
*humidity = buffer[0];
*temperature = buffer[2];
}
else
{
response = 2;
}
}
return response;
}
```
使用方法:
1. 将以上代码保存为`dht11.h`和`dht11.c`文件,并将其添加到工程中。
2. 在需要使用DHT11传感器的文件中添加以下代码:
```c
#include "dht11.h"
uint8_t humidity, temperature;
int main(void)
{
HAL_Init();
/* 初始化GPIO */
GPIO_InitTypeDef GPIO_InitStruct;
__HAL_RCC_GPIOA_CLK_ENABLE();
GPIO_InitStruct.Pin = DHT11_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(DHT11_PORT, &GPIO_InitStruct);
HAL_GPIO_WritePin(DHT11_PORT, DHT11_PIN, GPIO_PIN_RESET);
/* 读取温湿度数据 */
uint8_t response = DHT11_Read_Data(&humidity, &temperature);
if(response == 0)
{
/* 温湿度数据读取成功 */
printf("湿度:%d%%,温度:%d℃\n", humidity, temperature);
}
else if(response == 1)
{
/* DHT11无响应 */
printf("DHT11无响应\n");
}
else if(response == 2)
{
/* 校验和错误 */
printf("校验和错误\n");
}
while(1);
}
```
注意:需要根据实际的引脚和端口号进行修改。
"DHT11.h""DHT11.C"OLED.h"OLED.C"
"DHT11.h"和"DHT11.c"是用于与DHT11温湿度传感器进行通信的头文件和源文件。它们包含了初始化GPIO引脚、启动DHT11传感器、获取一个字节的数据等功能的代码。而"OLED.h"和"OLED.c"是用于与OLED显示屏进行通信的头文件和源文件。它们包含了与OLED屏幕进行初始化、显示文本、显示图像等功能的代码。这些文件的作用是为了方便用户在STM32上测量空气的温度和湿度,并将数据显示在OLED屏幕上。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)