#define POWER(x).((x)*(x)) main(){ int i=1; while (i<-4) printf(%d\t",POWER(i++)) ; printf ("\n"); }
时间: 2023-12-07 07:05:04 浏览: 89
这段代码有语法错误,应该是:
```
#define POWER(x) ((x)*(x))
int main() {
int i=1;
while (i > -4) {
printf("%d\t", POWER(i++));
}
printf("\n");
return 0;
}
```
这段代码的作用是定义了一个宏 `POWER`,用来计算一个数的平方。然后在 `main` 函数中,从 1 开始循环计数,每次计算出当前数的平方并输出,直到计数变为 -4 为止。输出的结果应该是 `1 4 9 16`。
相关问题
#define POWER(x) ((x)*(x)) int main() { int i=1; while (i <=4) { printf("%d\t", POWER(i++)); } printf("\n"); return 0; }
这段代码的输出结果是:1 4 9 16。
宏定义 POWER(x) ((x)*(x)) 定义了一个宏函数,用于计算 x 的平方。在主函数中,先将 i 赋值为 1,然后进入循环。每次循环中,先输出 POWER(i++) 的值,即 i 的平方,再将 i 自增 1。由于 i 的初始值为 1,因此第一次循环输出 1 的平方,即 1;第二次循环输出 2 的平方,即 4;第三次循环输出 3 的平方,即 9;第四次循环输出 4 的平方,即 16。最后输出一个换行符,结束程序。
/* * File: ADC.c * Author: tlfte *AD转换,结果在C口和D口的LED上显示,能进行各种通道选择和参考电压,结果对齐方式选择 * Created on 2018年8月6日, 上午10:07 练习AD结果的计算验证,AD_RESULT=VIN×1023÷VREF,讲解887头文件的作用 */ // PIC16F887 Configuration Bit Settings // 'C' source line config statements // CONFIG1 #pragma config FOSC = XT // Oscillator Selection bits (XT oscillator: Crystal/resonator on RA6/OSC2/CLKOUT and RA7/OSC1/CLKIN) #pragma config WDTE = OFF // Watchdog Timer Enable bit (WDT disabled and can be enabled by SWDTEN bit of the WDTCON register) #pragma config PWRTE = OFF // Power-up Timer Enable bit (PWRT disabled) #pragma config MCLRE = ON // RE3/MCLR pin function select bit (RE3/MCLR pin function is digital input, MCLR internally tied to VDD) #pragma config CP = OFF // Code Protection bit (Program memory code protection is disabled) #pragma config CPD = OFF // Data Code Protection bit (Data memory code protection is disabled) #pragma config BOREN = OFF // Brown Out Reset Selection bits (BOR disabled) #pragma config IESO = OFF // Internal External Switchover bit (Internal/External Switchover mode is disabled) #pragma config FCMEN = OFF // Fail-Safe Clock Monitor Enabled bit (Fail-Safe Clock Monitor is disabled) #pragma config LVP = OFF // Low Voltage Programming Enable bit (RB3 pin has digital I/O, HV on MCLR must be used for programming) // CONFIG2 #pragma config BOR4V = BOR40V // Brown-out Reset Selection bit (Brown-out Reset set to 4.0V) #pragma config WRT = OFF // Flash Program Memory Self Write Enable bits (Write protection off) // #pragma config statements should precede project file includes. // Use project enums instead of #define for ON and OFF. #include <xc.h> #define _XTAL_FREQ 4000000 //指明时钟晶振为4MHz,使delay宏定义可以正常使用 void CSH(void); unsigned int AD_SUB(char k); void main( ) { unsigned int y; CSH(); while(1) { __delay_ms(100); //每隔100毫秒循环一次 y=AD_
SUB(0b00000110); //选择通道为AN6,即RA2口 PORTD=y; //将结果的低8位输出到D口LED灯上 y>>=8; //将结果的高8位移位到低8位 PORTC=y; //将结果的高8位输出到C口LED灯上 } } void CSH(void) //初始化函数 { TRISA=0xff; TRISC=0x00; TRISD=0x00; ANSEL=0x40; //选择AN6通道为模拟输入 ADCON1=0xC0; //设置参考电压为VDD和VSS,右对齐结果 } unsigned int AD_SUB(char k) //AD转换函数 { unsigned int AD_RESULT; ADCON0=k<<2; //将选择的通道左移两位,放到ADCON0的低4位上,同时清除其他位 ADCON0|=0x03; //启动AD转换 while(ADCON0&0x02); //等待AD转换完成 AD_RESULT=ADRESH; //将结果的高8位移位到低8位 AD_RESULT<<=8; //将结果的低8位移位到高8位 AD_RESULT|=ADRESL; //将结果的低8位放入结果的低8位上 return AD_RESULT; }