将rtthread串口为115200波特率
时间: 2023-11-17 14:08:44 浏览: 51
可以通过以下命令将rt-thread串口波特率设置为115200:
rtconfig.h 文件中:
将UART_BUFSZ 宏定义值从128改为1024
将UART_DEVICE_MAX 宏定义值从4改为1
在bsp.c 文件中:
rt_hw_uart_init("uart1", /*设备名称*/
USART1, /*USART1 */
GPIOB, GPIO_Pin_6, GPIO_Pin_7, /*USART1 GPIO*/
IRQ_USART1, /*中断号*/
115200); /*波特率*/
注意:以上回答仅供参考,具体实现方式需要根据您的具体需求和应用场景进行适当调整。
相关问题
rtthread串口中断接收
在RT-Thread中,串口接收可以通过中断方式实现。具体实现步骤如下:
1. 配置串口设备
通过RT-Thread的设备驱动框架,可以配置串口设备。在串口设备初始化的过程中,需要指定串口号、波特率等参数。
例如,配置COM1串口,波特率为115200,数据位为8位,无校验位,停止位为1位,可以使用以下代码:
```c
/* 获取串口设备 */
struct serial_device *serial = (struct serial_device *)rt_device_find("uart1");
/* 配置串口参数 */
struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT;
config.baud_rate = BAUD_RATE_115200;
config.data_bits = DATA_BITS_8;
config.stop_bits = STOP_BITS_1;
config.parity = PARITY_NONE;
/* 打开串口设备 */
rt_device_open(&serial->parent, RT_DEVICE_FLAG_INT_RX);
```
2. 实现串口接收中断处理函数
使用RT-Thread的中断处理机制,可以实现串口接收中断处理函数。在中断处理函数中,可以读取串口接收缓冲区中的数据,并进行处理。
例如,实现COM1串口接收中断处理函数,可以使用以下代码:
```c
/* 定义中断处理函数 */
void uart1_rx_isr(int vector, void *param)
{
RT_ASSERT(param != RT_NULL);
struct serial_device *serial = (struct serial_device *)param;
/* 读取接收缓冲区中的数据 */
while (serial->parent.rx_indicate(serial, 0) == 1)
{
rt_kprintf("received: %c\n", serial->parent.rx_buffer);
}
}
/* 注册中断处理函数 */
rt_hw_interrupt_install(IRQ_UART1_RX, uart1_rx_isr, (void *)serial, "uart1_rx");
```
在中断处理函数中,通过读取串口设备的rx_indicate函数来获取接收缓冲区中的数据。如果返回值为1,表示接收缓冲区中有数据可以读取,此时可以通过串口设备的rx_buffer成员来获取数据。
3. 启用串口接收中断
在串口设备初始化之后,需要启用串口接收中断。可以使用RT-Thread的设备接口函数rt_device_control来启用中断。
例如,启用COM1串口接收中断,可以使用以下代码:
```c
/* 启用串口接收中断 */
rt_device_control(&serial->parent, RT_DEVICE_CTRL_SET_INT, (void *)IRQ_UART1_RX);
```
启用中断之后,当串口接收缓冲区中有数据时,中断处理函数就会被调用,从而实现串口接收的功能。
stm32的rtthread 双串口程序
以下是一个基于STM32和RT-Thread操作系统的双串口程序示例:
```c
#include <rtthread.h>
#include <rtdevice.h>
#define USART1_CONFIG \
{ \
.name = "uart1", \
.parent_name = "serial", \
.open_flag = RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX | RT_DEVICE_FLAG_INT_TX, \
.close_flag = 0, \
.read = rt_serial_read, \
.write = rt_serial_write, \
.control = rt_serial_control \
}
#define USART2_CONFIG \
{ \
.name = "uart2", \
.parent_name = "serial", \
.open_flag = RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX | RT_DEVICE_FLAG_INT_TX, \
.close_flag = 0, \
.read = rt_serial_read, \
.write = rt_serial_write, \
.control = rt_serial_control \
}
static struct rt_serial_configure usart1_config = RT_SERIAL_CONFIG_DEFAULT;
static struct rt_serial_configure usart2_config = RT_SERIAL_CONFIG_DEFAULT;
rt_err_t usart1_rx_ind(rt_device_t dev, rt_size_t size)
{
/* do something when receive interrupt happens */
}
rt_err_t usart2_rx_ind(rt_device_t dev, rt_size_t size)
{
/* do something when receive interrupt happens */
}
void usart1_tx_complete(void *arg)
{
/* do something when transmit complete interrupt happens */
}
void usart2_tx_complete(void *arg)
{
/* do something when transmit complete interrupt happens */
}
int main(void)
{
rt_device_t usart1, usart2;
/* initialize USART1 and USART2 configurations */
usart1_config.baud_rate = 115200;
usart2_config.baud_rate = 9600;
/* register USART1 and USART2 devices */
usart1 = rt_serial_register(&USART1_CONFIG, &usart1_config);
usart2 = rt_serial_register(&USART2_CONFIG, &usart2_config);
/* set interrupt callback functions for USART1 and USART2 receive events */
rt_device_set_rx_indicate(usart1, usart1_rx_ind);
rt_device_set_rx_indicate(usart2, usart2_rx_ind);
/* set interrupt callback functions for USART1 and USART2 transmit events */
rt_device_set_tx_complete(usart1, usart1_tx_complete);
rt_device_set_tx_complete(usart2, usart2_tx_complete);
/* open USART1 and USART2 devices */
rt_device_open(usart1, RT_DEVICE_FLAG_INT_RX | RT_DEVICE_FLAG_INT_TX);
rt_device_open(usart2, RT_DEVICE_FLAG_INT_RX | RT_DEVICE_FLAG_INT_TX);
while (1) {
/* do something */
}
}
```
在这个示例中,首先定义了两个串口设备的配置信息结构体 `usart1_config` 和 `usart2_config`,分别对应 USART1 和 USART2。然后使用 `rt_serial_register` 函数注册这两个串口设备,并设置接收和发送的回调函数。最后使用 `rt_device_open` 函数打开两个串口设备,开始接收和发送数据。在主循环中,可以执行其他任务。
需要注意的是,在此示例中,串口设备的父节点为 "serial",因此需要先在RT-Thread的设备管理器中注册一个名为 "serial" 的设备,才能注册和打开 USART1 和 USART2 等串口设备。
此外,还需要根据实际情况修改串口的波特率、数据位、停止位、校验位等参数。
相关推荐
![doc](https://img-home.csdnimg.cn/images/20210720083327.png)
![doc](https://img-home.csdnimg.cn/images/20210720083327.png)
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)