stm32f103c8t6的rom最大可以设置0x2000吗
时间: 2024-05-15 21:10:54 浏览: 9
stm32f103c8t6是一款基于ARM Cortex-M3内核的微控制器,它的ROM(Read Only Memory)大小是64KB。在手册中没有提到可以设置ROM大小的最大值为0x2000。ROM在芯片制造时就已经被编程,用户无法修改ROM的大小。用户可以使用Flash(闪存)和SRAM(静态随机存储器)存储程序和数据。
相关问题
stm32f103c8t6通过DS18B20采集温度
要通过STM32F103C8T6采集DS18B20温度,需要按照以下步骤进行:
1. 连接DS18B20传感器:将DS18B20的VCC引脚连接到STM32F103C8T6的5V引脚,将GND引脚连接到STM32F103C8T6的GND引脚,将DQ引脚连接到STM32F103C8T6的GPIO引脚。
2. 在STM32F103C8T6上配置GPIO引脚:在使用DS18B20传感器时,需要使用STM32F103C8T6的GPIO引脚作为数据传输线。在程序中需要将该引脚设置为输出模式,并将其拉高,然后在发送数据时将其拉低。
3. 通过OneWire协议进行通信:DS18B20传感器使用的是Dallas的OneWire协议进行通信。在程序中需要按照OneWire协议的要求,对传感器进行初始化、发送指令、接收数据等操作。
4. 解析温度数据:DS18B20传感器返回的温度数据是一个16位的二进制数,需要将其转换为实际的温度值。具体的转换方法可以参考DS18B20的数据手册。
下面是一个简单的示例代码,仅供参考:
```c
#include "stm32f10x.h"
#define DQ_PIN GPIO_Pin_0
#define DQ_GPIO GPIOA
void delay_us(uint32_t us) {
uint32_t i;
for (i = 0; i < us * 8; i++) {
asm("NOP");
}
}
void DS18B20_Init(void) {
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = DQ_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(DQ_GPIO, &GPIO_InitStructure);
GPIO_SetBits(DQ_GPIO, DQ_PIN);
delay_us(1000);
}
void DS18B20_Write_Byte(uint8_t dat) {
uint8_t i;
for (i = 0; i < 8; i++) {
GPIO_ResetBits(DQ_GPIO, DQ_PIN); // 拉低数据线
delay_us(2);
GPIO_WriteBit(DQ_GPIO, DQ_PIN, (BitAction)(dat & 0x01)); // 发送数据
dat >>= 1;
delay_us(60);
GPIO_SetBits(DQ_GPIO, DQ_PIN); // 恢复数据线
}
}
uint8_t DS18B20_Read_Byte(void) {
uint8_t i;
uint8_t dat = 0;
for (i = 0; i < 8; i++) {
GPIO_ResetBits(DQ_GPIO, DQ_PIN); // 拉低数据线
delay_us(2);
dat >>= 1;
if (GPIO_ReadInputDataBit(DQ_GPIO, DQ_PIN)) {
dat |= 0x80; // 读取数据
}
delay_us(60);
GPIO_SetBits(DQ_GPIO, DQ_PIN); // 恢复数据线
}
return dat;
}
void DS18B20_Start(void) {
DS18B20_Init();
DS18B20_Write_Byte(0xcc); // 跳过ROM操作
DS18B20_Write_Byte(0x44); // 启动温度转换
delay_us(1000);
}
float DS18B20_Read_Temp(void) {
uint8_t temp_l, temp_h;
int16_t temp_value;
DS18B20_Start();
DS18B20_Init();
DS18B20_Write_Byte(0xcc); // 跳过ROM操作
DS18B20_Write_Byte(0xbe); // 读取温度值
temp_l = DS18B20_Read_Byte();
temp_h = DS18B20_Read_Byte();
temp_value = temp_h;
temp_value <<= 8;
temp_value |= temp_l;
return (float)temp_value / 16.0;
}
int main(void) {
float temp;
while (1) {
temp = DS18B20_Read_Temp();
// TODO: 处理温度数据
}
}
```
stm32f103c8t6控制DS18B20 模块的驱动程序
以下是一个简单的基于STM32F103C8T6控制DS18B20模块的驱动程序,使用的是OneWire协议。
首先需要在STM32的GPIO中设置DS18B20数据线的引脚为输出模式,并且设置成低电平,等待至少480us。接着将数据线拉高,并延时60us。然后将数据线设置为输入模式,等待DS18B20返回低电平,表示设备已经准备好了。最后开始发送指令,读取温度值。
```c
#include "stm32f10x.h"
#define DS18B20_PORT GPIOA
#define DS18B20_PIN GPIO_Pin_0
void delay_us(uint32_t us) {
us *= 8;
while (us--) {
__NOP();
}
}
void DS18B20_Init() {
GPIO_InitTypeDef GPIO_InitStruct;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStruct.GPIO_Pin = DS18B20_PIN;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_Out_OD;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(DS18B20_PORT, &GPIO_InitStruct);
GPIO_SetBits(DS18B20_PORT, DS18B20_PIN);
delay_us(500);
}
void DS18B20_WriteByte(uint8_t byte) {
uint8_t i;
for (i = 0; i < 8; i++) {
GPIO_ResetBits(DS18B20_PORT, DS18B20_PIN);
delay_us(2);
if (byte & 0x01) {
GPIO_SetBits(DS18B20_PORT, DS18B20_PIN);
}
delay_us(60);
GPIO_SetBits(DS18B20_PORT, DS18B20_PIN);
byte = byte >> 1;
delay_us(2);
}
}
uint8_t DS18B20_ReadByte() {
uint8_t i, byte = 0;
for (i = 0; i < 8; i++) {
GPIO_ResetBits(DS18B20_PORT, DS18B20_PIN);
delay_us(2);
GPIO_SetBits(DS18B20_PORT, DS18B20_PIN);
delay_us(15);
byte |= GPIO_ReadInputDataBit(DS18B20_PORT, DS18B20_PIN) << i;
delay_us(45);
}
return byte;
}
float DS18B20_ReadTemperature() {
uint8_t temp1, temp2;
float temperature;
DS18B20_WriteByte(0xCC); // skip ROM
DS18B20_WriteByte(0x44); // start conversion
while (!GPIO_ReadInputDataBit(DS18B20_PORT, DS18B20_PIN)); // wait for conversion
DS18B20_WriteByte(0xCC); // skip ROM
DS18B20_WriteByte(0xBE); // read scratchpad
temp1 = DS18B20_ReadByte();
temp2 = DS18B20_ReadByte();
temperature = (temp2 << 8 | temp1) * 0.0625;
return temperature;
}
```
在主函数中,可以调用DS18B20_Init()初始化DS18B20模块,然后调用DS18B20_ReadTemperature()函数读取温度值。
```c
int main(void) {
float temperature;
DS18B20_Init();
while (1) {
temperature = DS18B20_ReadTemperature();
printf("Temperature: %f\r\n", temperature);
delay_ms(1000);
}
}
```