请编写一个单片机串口驱动
时间: 2023-09-03 22:07:22 浏览: 36
这里提供一个基于STM32F103C8T6单片机的串口驱动代码,可供参考:
```c
#include "stm32f10x.h"
#define USART1_TX_GPIO_PORT GPIOA
#define USART1_TX_GPIO_PIN GPIO_Pin_9
#define USART1_RX_GPIO_PORT GPIOA
#define USART1_RX_GPIO_PIN GPIO_Pin_10
void USART1_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = USART1_TX_GPIO_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(USART1_TX_GPIO_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = USART1_RX_GPIO_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(USART1_RX_GPIO_PORT, &GPIO_InitStructure);
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
}
void USART1_SendByte(uint8_t byte)
{
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
USART_SendData(USART1, byte);
}
uint8_t USART1_ReceiveByte(void)
{
while (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET);
return (uint8_t)(USART_ReceiveData(USART1) & 0xFF);
}
void USART1_SendData(uint8_t *pData, uint16_t len)
{
uint16_t i;
for (i = 0; i < len; i++)
{
USART1_SendByte(pData[i]);
}
}
void USART1_ReceiveData(uint8_t *pData, uint16_t len)
{
uint16_t i;
for (i = 0; i < len; i++)
{
pData[i] = USART1_ReceiveByte();
}
}
```
这段代码实现了串口1的初始化配置和发送接收功能。其中,需要注意的是:
1. 串口1使用的GPIO引脚为PA9和PA10,可以根据需要修改为其他引脚。
2. 串口波特率为115200,可以根据需要修改为其他波特率。
3. 串口发送和接收函数中使用了USART_GetFlagStatus函数和USART_SendData/USART_ReceiveData函数,需要在代码中包含stm32f10x_usart.h头文件。
以上代码仅供参考,具体实现需要根据实际需求进行调整和完善。