写一个stm32 的串口接收函数
时间: 2024-02-24 07:17:57 浏览: 17
下面是一个示例代码,用于在STM32上编写串口接收函数:
```c
#include "stm32f4xx.h"
#define BUFFER_SIZE 128
volatile uint8_t rxBuffer[BUFFER_SIZE];
volatile uint8_t rxIndex = 0;
void USART2_IRQHandler(void) {
if (USART_GetITStatus(USART2, USART_IT_RXNE) != RESET) { // 检查是否接收到数据
uint8_t data = USART_ReceiveData(USART2); // 读取接收到的数据
if (rxIndex < BUFFER_SIZE) {
rxBuffer[rxIndex++] = data; // 存储数据到接收缓冲区
}
}
}
int main(void) {
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// 使能串口2时钟
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);
// 使能GPIOA时钟
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
// 配置PA2作为USART2的TX引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP ;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置PA3作为USART2的RX引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 将引脚连接到USART功能
GPIO_PinAFConfig(GPIOA, GPIO_PinSource2, GPIO_AF_USART2);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource3, GPIO_AF_USART2);
// 配置USART2
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART2, &USART_InitStructure);
// 配置USART2接收中断
NVIC_InitStructure.NVIC_IRQChannel = USART2_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
// 使能USART2接收中断
USART_ITConfig(USART2, USART_IT_RXNE, ENABLE);
// 使能USART2
USART_Cmd(USART2, ENABLE);
while (1) {
// 在这里可以处理接收到的数据
if (rxIndex > 0) {
// 处理接收缓冲区中的数据
// ...
rxIndex = 0; // 清空接收缓冲区索引
}
}
}
```
以上代码演示了如何在STM32上配置和使用USART2进行串口接收。在USART2的中断处理函数中(`USART2_IRQHandler`),通过检查`USART_GetITStatus(USART2, USART_IT_RXNE)`来判断是否接收到数据。如果接收到数据,使用`USART_ReceiveData(USART2)`读取接收到的数据,并将其存储到接收缓冲区`rxBuffer`中。
在主函数中,可以通过处理接收缓冲区的数据来进行相应的操作。请注意,这只是一个示例,你可以根据自己的需求进行进一步的处理。