配置stm32串口代码
时间: 2023-08-12 19:07:59 浏览: 40
以下是基本的STM32串口配置代码,你需要根据自己的具体硬件和需求进行修改:
```c
#include "stm32f4xx.h"
void USART_Config(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
USART_InitTypeDef USART_InitStruct;
// 使能 USART1 和 GPIOA 时钟
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
// 配置 USART1_TX (PA9) 和 USART1_RX (PA10) 为复用功能
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStruct);
// 将 USART1_TX 和 USART1_RX 连接到复用引脚上
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_USART1);
//USART1 初始化设置
USART_InitStruct.USART_BaudRate = 115200; //波特率设置
USART_InitStruct.USART_WordLength = USART_WordLength_8b;//字长为8位数据格式
USART_InitStruct.USART_StopBits = USART_StopBits_1;//一个停止位
USART_InitStruct.USART_Parity = USART_Parity_No;//无奇偶校验位
USART_InitStruct.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//无硬件数据流控制
USART_InitStruct.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;//收发模式
USART_Init(USART1, &USART_InitStruct); //初始化串口1
USART_Cmd(USART1, ENABLE); //使能串口1
}
```
以上代码是在使用USART1作为串口的情况下的配置代码,你可以根据具体情况修改GPIO的引脚和USART模块的编号。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)