编写一个stm32f103c8t6使用ch05蓝牙模块的串口通信
时间: 2023-08-02 19:07:05 浏览: 41
以下是一个使用STM32F103C8T6微控制器和CH05蓝牙模块进行串口通信的示例代码:
```c
#include "stm32f10x.h"
#include <stdio.h>
#define USARTx USART1
#define USARTx_IRQn USART1_IRQn
#define USARTx_GPIO GPIOA
#define USARTx_GPIO_RCC RCC_APB2Periph_GPIOA
#define USARTx_RCC RCC_APB2Periph_USART1
void USART_Configuration(uint32_t baudrate)
{
USART_InitTypeDef USART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// 使能GPIO和USART时钟
RCC_APB2PeriphClockCmd(USARTx_GPIO_RCC | USARTx_RCC, ENABLE);
// 配置USART引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(USARTx_GPIO, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(USARTx_GPIO, &GPIO_InitStructure);
// 配置USART参数
USART_InitStructure.USART_BaudRate = baudrate;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USARTx, &USART_InitStructure);
// 使能USART接收中断
USART_ITConfig(USARTx, USART_IT_RXNE, ENABLE);
// 使能USART
USART_Cmd(USARTx, ENABLE);
}
void NVIC_Configuration(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
// 配置USART中断通道
NVIC_InitStructure.NVIC_IRQChannel = USARTx_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
void USARTx_IRQHandler(void)
{
if (USART_GetITStatus(USARTx, USART_IT_RXNE) != RESET)
{
// 接收到数据,进行相应的处理
uint8_t received_data = USART_ReceiveData(USARTx);
// 在这里添加处理接收到的数据的代码
// 示例:将接收到的数据回传
USART_SendData(USARTx, received_data);
// 清除接收中断标志位
USART_ClearITPendingBit(USARTx, USART_IT_RXNE);
}
}
int main(void)
{
USART_Configuration(9600); // 设置波特率为9600
NVIC_Configuration();
while (1)
{
// 在这里添加需要执行的任务
// 示例:发送数据
uint8_t data_to_send = 0xAA;
USART_SendData(USARTx, data_to_send);
// 延时一段时间
for (volatile int i = 0; i < 1000000; i++);
}
}
```
以上代码设置了USART1作为串口通信接口,并配置波特率为9600。在USART1的中断处理函数`USARTx_IRQHandler`中,接收到的数据将进行处理,并通过串口发送回传。你可以根据需要在主循环中添加需要执行的任务。请注意,此示例代码只提供了基本的框架,你需要根据具体的需求进行修改和完善。