写一段hx711的驱动代码
时间: 2023-12-01 18:56:49 浏览: 28
Sure, here is an example code for driving the HX711:
```
#include <hx711.h>
#define HX711_DOUT 3
#define HX711_SCK 2
HX711 scale(HX711_DOUT, HX711_SCK);
void setup() {
Serial.begin(9600);
scale.set_scale(2280.f); // set this to your calibration factor
scale.tare(); // reset the scale to 0
}
void loop() {
Serial.print("Reading: ");
Serial.println(scale.get_units(), 2);
delay(1000);
}
```
Remember to adjust the calibration factor based on your setup. Hope this helps!
相关问题
stm32f103 和 hx711驱动代码
以下是 STM32F103 和 HX711 的驱动代码,供参考:
```c
#include "stm32f10x.h"
#define HX711_GPIO GPIOA
#define HX711_PIN_SCK GPIO_Pin_4
#define HX711_PIN_DOUT GPIO_Pin_5
void HX711_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = HX711_PIN_SCK;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(HX711_GPIO, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = HX711_PIN_DOUT;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(HX711_GPIO, &GPIO_InitStructure);
}
uint32_t HX711_Read(void)
{
uint8_t i;
uint32_t value = 0;
GPIO_ResetBits(HX711_GPIO, HX711_PIN_SCK);
while(GPIO_ReadInputDataBit(HX711_GPIO, HX711_PIN_DOUT));
for(i=0; i<24; i++)
{
GPIO_SetBits(HX711_GPIO, HX711_PIN_SCK);
value = value << 1;
GPIO_ResetBits(HX711_GPIO, HX711_PIN_SCK);
if(GPIO_ReadInputDataBit(HX711_GPIO, HX711_PIN_DOUT))
value++;
}
GPIO_SetBits(HX711_GPIO, HX711_PIN_SCK);
value = value ^ 0x800000;
GPIO_ResetBits(HX711_GPIO, HX711_PIN_SCK);
return value;
}
```
上述代码中,`HX711_GPIO` 定义了 HX711 模块所使用的 GPIO 端口, `HX711_PIN_SCK` 定义了 SCK 引脚, `HX711_PIN_DOUT` 定义了 DOUT 引脚。`HX711_Init()` 函数用于对引脚进行初始化,`HX711_Read()` 函数用于读取 HX711 模块的值。
需要注意的是,这里的代码只是示例代码,具体的引脚配置需要根据实际情况进行修改。
写一段hx711的c程序
好的,以下是一个简单的hx711的C程序:
```c
#include <stdio.h>
#include <wiringPi.h>
#define SCK_PIN 0 // SCLK引脚
#define DT_PIN 2 // DATA引脚
int HX711_Read() {
int data = 0;
int i;
// 等待传感器复位完成
while (digitalRead(DT_PIN) == 1);
// 读取24位数据
for (i = 0; i < 24; i++) {
digitalWrite(SCK_PIN, HIGH);
data <<= 1;
if (digitalRead(DT_PIN))
data++;
digitalWrite(SCK_PIN, LOW);
}
// 去掉最高位符号位,转成有符号数
data ^= 0x800000;
return data;
}
int main() {
int val;
wiringPiSetup();
pinMode(SCK_PIN, OUTPUT);
pinMode(DT_PIN, INPUT);
while (1) {
val = HX711_Read();
printf("Weight: %d\n", val);
}
return 0;
}
```
以上是读取HX711模块的重量数据的程序。注释中详细说明了程序的处理流程和具体实现方法。需要注意的是,在运行程序之前,需要先将SCLK和DT引脚与树莓派的GPIO口连接好。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)