void USART2_Configuration(void) { USART_InitTypeDef USART_InitStructure; GPIO_InitTypeDef GPIO_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO, ENABLE); RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); // USART2 Tx (PA.02) configuration GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOA, &GPIO_InitStructure); // USART2 Rx (PA.03) configuration GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING; GPIO_Init(GPIOA, &GPIO_InitStructure);
时间: 2024-04-22 14:29:00 浏览: 22
这段代码是用于配置STM32的USART2串口相关的GPIO口的函数。首先定义USART_InitTypeDef和GPIO_InitTypeDef结构体变量USART_InitStructure和GPIO_InitStructure,用于配置USART2串口和GPIO口。然后开启GPIOA和AFIO的时钟,开启USART2串口的时钟。接着配置USART2的Tx引脚(PA.02)为推挽输出模式,最大输出速率为50MHz,配置USART2的Rx引脚(PA.03)为悬空输入模式。最后通过GPIO_Init函数将这些配置应用到对应的GPIO口上。这段代码的作用是配置USART2的Tx和Rx引脚,使之能够进行数据的收发。
相关问题
#include "led.h" // Device header void GPIO_Configuration(void)//接口初始化 { GPIO_InitTypeDef GPIO_InitStructure;//将GPIO_Initstructure定义为InitTypeDef类型的结构体 GPIO_InitStructure.GPIO_Pin=GPIO_Pin_10 ; GPIO_InitStructure.GPIO_Speed=GPIO_Speed_10MHz;//设置输出的频率为10MHz GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IN_FLOATING;//设置输出模式为浮空输出模式 GPIO_Init(GPIOA,&GPIO_InitStructure);//初始化GPIOB GPIO_InitStructure.GPIO_Pin=GPIO_Pin_9 ; GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;//设置输出的频率为10MHz GPIO_InitStructure.GPIO_Mode=GPIO_Mode_AF_PP;//设置输出模式为推挽输出模式 GPIO_Init(GPIOA,&GPIO_InitStructure);//初始化GPIOA } void RCC_Configuration(void) { RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO, ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); } void USART_Configuration(void) { USART_InitTypeDef USART_InitStructure; USART_InitStructure.USART_BaudRate = 9600; USART_InitStructure.USART_WordLength = USART_WordLength_8b; USART_InitStructure.USART_StopBits = USART_StopBits_1; USART_InitStructure.USART_Parity = USART_Parity_No; USART_InitStructure.USART_HardwareFlowControl= USART_HardwareFlowControl_None; USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; USART_Init(USART1, &USART_InitStructure); USART_Cmd(USART1, ENABLE); }
这段代码主要是对 STM32 的串口和 GPIO 进行初始化配置。其中,GPIO_Configuration() 函数用于配置 GPIO 的输入输出模式、频率等;RCC_Configuration() 函数用于使能 GPIO 和 USART 的时钟;USART_Configuration() 函数则用于配置 USART 的波特率、数据位数、停止位等。
具体来说,GPIO_Configuration() 函数中,GPIOA_Pin_10 被设置为浮空输入模式,GPIOA_Pin_9 被设置为推挽输出模式,这意味着输入时,该引脚的电压不稳定,需要通过外部电路稳定电压;输出时,该引脚的电压可以被直接控制,输出高低电平。
在 RCC_Configuration() 函数中,RCC_APB2PeriphClockCmd() 用于使能 GPIOA 和 AFIO 的时钟,表示允许这些模块工作;RCC_APB2PeriphClockCmd() 用于使能 USART1 的时钟,表示允许该串口通信。
在 USART_Configuration() 函数中,USART_InitTypeDef 结构体中设置了串口的一些参数,如波特率、数据位数、停止位等;USART_Cmd() 函数则用于启动 USART1,使其能够进行通信。
void uart6_init(void) { RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE); RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2,ENABLE); GPIO_InitTypeDef GPIO_InitStructure; GPIO_InitStructure.GPIO_Mode=GPIO_Mode_AF_PP; GPIO_InitStructure.GPIO_Pin=GPIO_Pin_9|GPIO_Pin_10; GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz; //串口,数据传输,主要用于接收(接收函数) USART_InitTypeDef USART_InitStructure; USART_InitStructure.USART_BaudRate=115200; USART_InitStructure.USART_HardwareFlowControl=USART_HardwareFlowControl_None; USART_InitStructure.USART_Mode=USART_Mode_Rx|USART_Mode_Tx; USART_InitStructure.USART_Parity=USART_Parity_No;//极性 USART_InitStructure.USART_StopBits=USART_StopBits_1;//停止位 USART_InitStructure.USART_WordLength=USART_WordLength_8b;//字节长度 USART_ITConfig(USART2,USART_IT_RXNE,ENABLE);//中断使能,接收缓冲器 NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); NVIC_InitTypeDef NVIC_InitStructure; NVIC_InitStructure.NVIC_IRQChannel=USART2_IRQn; NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE; NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1; NVIC_InitStructure.NVIC_IRQChannelSubPriority=1; GPIO_Init(GPIOA,&GPIO_InitStructure); NVIC_Init(&NVIC_InitStructure); USART_Init(USART2,&USART_InitStructure); USART_Cmd(USART2,ENABLE); } void USART2_IRQHandler(void) { if(USART_GetITStatus(USART2,USART_FLAG_RXNE)==SET) { } USART_ClearITPendingBit(USART2,USART_FLAG_RXNE); }
这段代码存在几个错误:
1. 在初始化时,使用了不正确的宏定义。函数 `RCC_APB2PeriphClockCmd()` 和 `RCC_APB1PeriphClockCmd()` 应该分别使用 `RCC_APB2PeriphClockCmd()` 和 `RCC_APB1PeriphClockCmd()` 来初始化 GPIOA 和 USART2 模块。
2. 在初始化 GPIO 时,使用了不正确的 GPIO 引脚。GPIO_Pin_9 和 GPIO_Pin_10 分别对应 USART1 的引脚 PA9 和 PA10,而不是 USART2 的引脚。因此,这些引脚需要更改为正确的引脚。
3. 在初始化 USART 时,使用了不正确的 USART 模块。应该将 `USART2` 改为 `USART1`,因为我们要初始化的是 USART1 模块。
4. 在中断处理函数 `USART2_IRQHandler()` 中,缺少接收数据的处理逻辑。你需要在中断处理函数中添加处理接收数据的代码。
最后,缺少返回值 `return 0;`。完整的代码如下:
```c
void uart6_init(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10; // 已修正
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
USART_InitTypeDef USART_InitStructure;
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE); // 已修正
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn; // 已修正
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
GPIO_Init(GPIOA, &GPIO_InitStructure);
NVIC_Init(&NVIC_InitStructure);
USART_Init(USART1, &USART_InitStructure); // 已修正
USART_Cmd(USART1, ENABLE);
}
void USART1_IRQHandler(void) // 已修正
{
if (USART_GetITStatus(USART1, USART_IT_RXNE) == SET)
{
// 处理接收数据的代码
}
USART_ClearITPendingBit(USART1, USART_IT_RXNE);
}
```
这段代码初始化了 STM32 单片机的 USART1 模块,并添加了接收数据的中断处理函数。