没有合适的资源?快使用搜索试试~ 我知道了~
首页H3C WA4320-ACN-E无线AP快速安装教程:必备工具与详细步骤
H3C WA4320-ACN-E无线AP快速安装教程:必备工具与详细步骤
需积分: 50 17 下载量 192 浏览量
更新于2023-05-19
1
收藏 1.41MB PDF 举报
H3C WA4320-ACN-E无线接入点快速安装指南-6PW106是一份详细的手册,旨在指导用户快速安装这款AP。该手册首先强调了重要性,即AP不随设备一起提供安装工具,用户需自行准备包括尖嘴钳、剥线钳、电钻、橡胶锤、记号笔、十字螺丝刀和斜口钳在内的基本工具。这些工具在安装过程中扮演着关键角色,如定位和固定AP支架。 安装附件介绍部分详细介绍了用于壁挂和吸顶安装的附件,例如壁挂安装件带有M4×7mm的螺丝孔,用户需要确保安装件和AP支架的螺孔对齐,并使用螺丝紧固,以稳固地固定AP到墙壁或天花板上。为了确保安全,手册指示用户在墙上标记安装位置并预钻孔,再使用膨胀螺栓固定安装件。 此外,手册还特别提到安装AP时应遵循最佳实践,建议与3G/4G基站和天线保持至少5米(16.40英尺)的距离,以减少信号干扰和提高网络性能。这显示了在规划网络部署时,不仅需要考虑物理安装,还要考虑无线信号的覆盖范围和干扰问题。 安装过程中的注意事项还包括电源供应,可能涉及安装专用的电源适配器或连接至现有的电力系统。在完成所有安装步骤后,这份指南可能会包含初步的配置和测试部分,确保AP能够正常运行并连接到网络。 H3C WA4320-ACN-E无线接入点快速安装指南提供了全面且实用的步骤,帮助用户在专业和高效的前提下完成AP的安装任务。对于任何进行此类设备安装的IT专业人士来说,这份文档是不可或缺的参考资料。
资源详情
资源推荐
Tool List 工具参考
The installation tools are not provided with the AP. Prepare them yourself.
AP不随机提供安装工具,请用户根据实际安装需求自备安装工具。
Introduction to Installation Accessories 安装附件介绍
1
2
3
4
Needle-nose pliers
尖嘴钳
Wire-stripping pliers
剥线钳
Drill
电钻
Rubber hammer
橡胶锤
Marker
记号笔
Phillips screwdriver
十字螺丝刀
Diagonal pliers
斜口钳
Align the screw hole in the AP bracket with the screw hole in the AP. Fasten the M4 × 7
mm pan-head screw to secure the AP bracket to the AP.
将安装件对准AP背面的螺孔,拧紧 M4×7 mm 螺钉,壁挂安装件固定到AP。
Mounting the AP on a wall 安装AP到墙面
30 mm
(1.18 in)
Use screws to attach the wall bracket to the wall.
使用螺钉将安装件固定到墙面。
Mark the installation hole locations on the wall for the wall bracket. Drill holes at the
marked locations. Hammer wall anchors into the holes.
在墙面使用记号笔标记出安装件安装孔的位置,使用电钻在标记处钻孔并将膨胀螺管使
用橡胶锤钉入安装孔。
Mounting the AP on a ceiling 吸顶安装
82 mm
(3.23 in)
1
2
H3C WA4320-ACN-E Access Point Installation Quick Start-6PW106
H3C WA4320-ACN-E无线接入点 快速安装指南-6PW106
Install the AP more than 5 m (16.40 ft) away from 3G/4G base stations and
antennas. AP的安装位置与3G/4G基站、天线的距离建议在5米以上。
AP bracket
AP安装件
Wall (Ceiling) bracket
壁挂(吸顶)安装件
Power adapter
(only supplied with the fat AP)
电源适配器(仅Fat AP随机附带)
Console cable
(only supplied with the fat AP)
Console 线缆仅Fat AP随机附带)
Wall anchor kit
膨胀螺管和螺钉
M4×7 bolt
M4×7盘头螺钉
Pan head screw
盘头螺钉
Align the AP with the wall bracket in the direction
as shown in the figure, and rotate the AP
clockwise until it clicks into place.
将AP按照如上图所示的方向对准墙面的壁挂安装
件,然后顺时针旋转至竖直位置,当听到“啪”的一
声时,说明AP已经锁紧,安装完毕。
Mark the installation hole locations on the
ceiling for the wall bracket. Drill holes at the
marked locations.
在天花板使用记号笔标记出安装件安装孔的
位置,然后用电钻在标记处钻孔。
×2 ×2 ×1
Use the M4 × 7 mm pan-head screw to secure the AP bracket to the AP.
请使用M4 × 7 mm 盘头螺钉将壁挂件固定到AP上,避免螺钉用错造成的设备损坏。
!
Install the AP more than 5 m (16.40 ft) away from 3G/4G base stations and
antennas. AP的安装位置与3G/4G基站、天线的距离建议在5米以上。
Align the AP with the wall bracket in the direction as shown in the figure, and rotate the
AP clockwise until it clicks into place.
将AP按照如上图所示的方向对准天花板的壁挂安装件,然后顺时针旋转至竖直位置,当
听到“啪”的一声时,说明AP已经锁紧,安装完毕。
Use pan head screws to attach the wall
bracket to the ceiling.
使用盘头螺钉将安装件固定到天花板。
BOM:3104A0Y5
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功