stm32cubemx dma串口通信printf
时间: 2023-09-25 21:11:54 浏览: 108
可以使用STM32CubeMX配置DMA来实现串口通信中的printf功能。下面是一个示例代码,可以将printf输出通过DMA发送到串口:
1. 首先,确保你已经在STM32CubeMX中启用了相关的USART和DMA功能,并正确配置了串口通信的参数。
2. 在生成的代码中找到USART相关的初始化函数,一般位于`usart.c`文件中。在该函数中,找到`HAL_UART_MspInit()`函数的实现。
3. 在`HAL_UART_MspInit()`函数的开头添加以下代码,用于初始化DMA传输相关的资源:
```c
/* DMA interrupt init */
/* DMA1_Channel4_IRQn interrupt configuration */
HAL_NVIC_SetPriority(DMA1_Channel4_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(DMA1_Channel4_IRQn);
```
4. 接下来,在`HAL_UART_MspInit()`函数中添加以下代码,用于配置DMA传输:
```c
/* Enable the DMA transfer for transmit */
__HAL_RCC_DMA1_CLK_ENABLE();
hdma_usart2_tx.Instance = DMA1_Channel4;
hdma_usart2_tx.Init.Direction = DMA_MEMORY_TO_PERIPH;
hdma_usart2_tx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_tx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;hdma_usart2_tx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_tx.Init.Mode = DMA_NORMAL;
hdma_usart2_tx.Init.Priority = DMA_PRIORITY_LOW;
if (HAL_DMA_Init(&hdma_usart2_tx) != HAL_OK)
{
Error_Handler();
}
/* Associate the initialized DMA handle to the UART handle */
__HAL_LINKDMA(huart, hdmatx, hdma_usart2_tx);
/* Enable the DMA transfer complete interrupt */
__HAL_UART_ENABLE_IT(huart, UART_IT_TC);
```
注意:上述代码中,使用的是USART2和DMA1_Channel4,你需要根据实际情况进行调整。
5. 在生成的代码中找到`USART_Transmit()`函数,一般位于`usart.c`文件中。在该函数中添加以下代码,用于启动DMA传输:
```c
/* Set the DMA transfer complete callback */
huart->hdmatx->XferCpltCallback = UART_DMA_TransmitCplt;
/* Start the DMA transfer */
HAL_DMA_Start_IT(huart->hdmatx, (uint32_t)str, strlen(str));
```
6. 最后,在生成的代码中找到`USART_IRQHandler()`函数,一般位于`stm32f4xx_it.c`文件中。在该函数中添加以下代码,用于处理DMA传输完成的中断:
```c
/* USART2 DMA Transmit Complete Interrupt */
void DMA1_Channel4_IRQHandler(void)
{
/* Check the DMA interrupt flag */
if (__HAL_DMA_GET_IT_SOURCE(huart2.hdmatx, DMA_IT_TC) != RESET)
{
/* Clear the DMA interrupt flag */
__HAL_DMA_CLEAR_FLAG(huart2.hdmatx, DMA_IT_TC);
/* Disable the DMA transfer complete interrupt */
__HAL_DMA_DISABLE_IT(huart2.hdmatx, DMA_IT_TC);
/* Call the DMA transmit complete callback function */
HAL_UART_TxCpltCallback(&huart2);
}
}
```
完成以上步骤后,你就可以在代码中使用标准的`printf`函数,输出的内容会通过DMA传输到串口中。
希望这对你有帮助!如有更多问题,请继续提问。