GPIO_InitTypeDef GPIO_InitStructure; GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_1)
时间: 2024-08-14 07:09:39 浏览: 34
GPIO_InitTypeDef是一个结构体,在许多基于微控制器的嵌入式开发环境中,如STM32系列,它用于初始化通用输入/输出(GPIO)端口。在这个定义中:
- GPIOA表示使用的GPIO端口A,这是STM32系统中的一个特定GPIO资源。
- GPIO_PinSource10指定了该配置作用于GPIOA的第10个引脚(通常从0开始计数)。
- GPIO_AF_1表示这个引脚将被配置为功能映射到AFE( Analogue Front-End)组1,这是一个常见的功能选择,例如连接到ADC或其他模拟外设。
通过GPIO_PinAFConfig函数,开发者可以设置GPIO引脚的 Alternate Function(备用功能),即除了基本的数字输入/输出之外,还可以将其映射到预定义的功能,如通信、定时等。这有助于简化硬件连接并提高代码复用性。
相关问题
void myUSART_Init() { RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA,ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1,ENABLE); GPIO_PinAFConfig(GPIOA,GPIO_PinSource9,GPIO_AF_USART1); GPIO_PinAFConfig(GPIOA,GPIO_PinSource10,GPIO_AF_USART1); GPIO_InitTypeDef GPIO_InitStructure; GPIO_InitStructure.GPIO_Mode =GPIO_Mode_AF; GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10; GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOB,&GPIO_InitStructure); USART_InitTypeDef USART_InitStuctyre; USART_InitStuctyre.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; USART_InitStuctyre.USART_Parity = USART_Parity_No; USART_InitStuctyre.USART_StopBits = USART_StopBits_1; USART_InitStuctyre.USART_BaudRate = 9600; USART_InitStuctyre.USART_WordLength = USART_WordLength_8b; USART_InitStuctyre.USART_HardwareFlowControl =USART_HardwareFlowControl_None; USART_Init(USART1,&USART_InitStuctyre); USART_Cmd(USART1,ENABLE); USART_ITConfig(USART1,USART_IT_TXE,ENABLE); NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); NVIC_InitTypeDef NVIC_InitStructure; NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn; NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3; NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 3; NVIC_Init(&NVIC_InitStructure); } void myUSARTsend_Byte(uint16_t Byte) { USART_SendData(USART1,Byte); while(USART_GetFlagStatus(USART1,USART_FLAG_TXE)==RESET); } void myUSARTsend_Array(uint8_t *Array,uint16_t Length) { uint16_t i; for(i=0;i<=Length;i++) { myUSARTsend_Byte(Array[i]); } }
这是一个使用 STM32F4 的 USART1 进行串口通信的初始化和发送函数的示例代码。
```c
void myUSART_Init()
{
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_USART1);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
USART_InitTypeDef USART_InitStructure;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
USART_ITConfig(USART1, USART_IT_TXE, ENABLE);
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 3;
NVIC_Init(&NVIC_InitStructure);
}
void myUSARTsend_Byte(uint16_t Byte)
{
USART_SendData(USART1, Byte);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
}
void myUSARTsend_Array(uint8_t *Array, uint16_t Length)
{
uint16_t i;
for (i = 0; i < Length; i++)
{
myUSARTsend_Byte(Array[i]);
}
}
```
`myUSART_Init()` 函数用于初始化 USART1,配置相关的 GPIO 和 USART 参数。`myUSARTsend_Byte()` 函数用于发送一个字节的数据,`myUSARTsend_Array()` 函数用于发送一个字节数组。
请注意,这只是一个简单的示例,你可能需要根据你的具体需求进行适当的修改。另外,还需要在程序中定义 USART1 的中断处理函数 `USART1_IRQHandler()` 来处理接收中断和其他相关操作。
gpio_pinafconfig函数
GPIO_PinAFConfig函数是STM32固件库提供的一个函数,用于配置GPIO引脚的复用功能。在STM32微控制器中,每个GPIO引脚可以配置为多种不同的功能,例如普通输入/输出、复用功能等。复用功能主要用于连接外设,如ADC、SPI、UART等。
该函数的原型如下:
```c
void GPIO_PinAFConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_PinSource, uint8_t GPIO_AF);
```
该函数需要传入三个参数:
- GPIOx:表示GPIO端口,可以是GPIOA、GPIOB、GPIOC等。
- GPIO_PinSource:表示GPIO引脚编号,可以是GPIO_Pin_0、GPIO_Pin_1、GPIO_Pin_2等。
- GPIO_AF:表示要配置的复用功能编号,可以是0~15之间的任意值。在不同的芯片型号中,GPIO_AF可能会有不同的含义和取值范围。
该函数的作用是将GPIO引脚配置为指定的复用功能。在调用该函数之前,需要先将GPIO引脚配置为复用功能模式,具体方法为调用GPIO_Init函数,并将GPIO_Mode参数设置为GPIO_Mode_AF。例如,以下代码将PA9引脚配置为USART1的Tx输出引脚:
```c
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
```
在上述代码中,GPIO_PinAFConfig函数将PA9引脚配置为USART1的Tx输出引脚,其中GPIO_AF_USART1是一个宏定义,表示USART1的复用功能编号。