写DS18B20的hal库获取温度
时间: 2024-04-12 09:30:30 浏览: 27
下面是一个使用HAL库获取DS18B20温度的示例代码:
```c
#include "stm32f4xx_hal.h" // 根据你的MCU型号选择正确的头文件
#define DS18B20_GPIO_PORT GPIOA // DS18B20连接的GPIO端口
#define DS18B20_GPIO_PIN GPIO_PIN_0 // DS18B20连接的GPIO引脚
#define DS18B20_CONVERT_CMD 0x44 // DS18B20温度转换命令
#define DS18B20_READ_SCRATCHPAD_CMD 0xBE // 读取DS18B20寄存器命令
UART_HandleTypeDef huart2; // 串口句柄
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART2_UART_Init(void);
void delay_us(uint32_t us)
{
uint32_t count = (SystemCoreClock / 1000000) * us;
while (count--)
{
}
}
void ds18b20_reset(void)
{
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_RESET);
delay_us(480);
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_SET);
delay_us(60);
if (HAL_GPIO_ReadPin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN) == GPIO_PIN_RESET)
{
while (HAL_GPIO_ReadPin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN) == GPIO_PIN_RESET);
}
delay_us(480);
}
void ds18b20_write_bit(uint8_t bit)
{
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_RESET);
delay_us(1);
if (bit)
{
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_SET);
}
delay_us(60);
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_SET);
}
uint8_t ds18b20_read_bit(void)
{
uint8_t bit = 0;
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_RESET);
delay_us(1);
HAL_GPIO_WritePin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN, GPIO_PIN_SET);
delay_us(15);
bit = HAL_GPIO_ReadPin(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN);
delay_us(45);
return bit;
}
void ds18b20_write_byte(uint8_t data)
{
uint8_t i;
for (i = 0; i < 8; i++)
{
ds18b20_write_bit(data & 0x01);
data >>= 1;
}
}
uint8_t ds18b20_read_byte(void)
{
uint8_t i;
uint8_t data = 0;
for (i = 0; i < 8; i++)
{
data >>= 1;
if (ds18b20_read_bit())
{
data |= 0x80;
}
}
return data;
}
float ds18b20_get_temperature(void)
{
uint8_t temp_l;
uint8_t temp_h;
float temperature;
ds18b20_reset();
ds18b20_write_byte(DS18B20_CONVERT_CMD);
HAL_Delay(750); // 等待转换完成,根据DS18B20的精度和供电方式调整延时时间
ds18b20_reset();
ds18b20_write_byte(DS18B20_READ_SCRATCHPAD_CMD);
temp_l = ds18b20_read_byte();
temp_h = ds18b20_read_byte();
temperature = (float)((temp_h << 8) | temp_l) / 16.0;
return temperature;
}
int main(void)
{
HAL_Init();
SystemClock_Config();
MX_GPIO_Init();
MX_USART2_UART_Init();
float temperature;
char uart_tx_buffer[32];
while (1)
{
temperature = ds18b20_get_temperature();
sprintf(uart_tx_buffer, "Temperature: %.2f\r\n", temperature);
HAL_UART_Transmit(&huart2, (uint8_t*)uart_tx_buffer, strlen(uart_tx_buffer), HAL_MAX_DELAY);
HAL_Delay(1000); // 延时1秒
}
}
```
在这个示例代码中,我们首先定义了连接DS18B20的GPIO端口和引脚。然后,我们实现了一些用于DS18B20通信的函数,如复位、写入位、读取位、写入字节和读取字节等。最后,我们实现了获取温度的函数`ds18b20_get_temperature()`,该函数通过发送命令和读取寄存器来获取DS18B20的温度值。
在`main()`函数中,我们不断调用`ds18b20_get_temperature()`函数获取温度,并通过串口发送到电脑上。
请根据你的具体硬件和需求,适当修改代码。