ds18b20温湿度传感器stm32f1hal
时间: 2023-09-07 15:13:56 浏览: 51
您好!对于DS18B20温湿度传感器的使用,您可以在STM32F1HAL库中进行编程操作。以下是一些基本的步骤来初始化和读取DS18B20传感器的温度数据:
1. 配置引脚:首先,您需要配置一个GPIO引脚作为DS18B20传感器的数据线。您可以使用HAL库的GPIO_Init()函数来设置引脚的输入/输出模式和速度。
2. 发送复位信号:通过将数据线拉低一段时间然后释放,发送复位信号来与传感器进行通信。使用GPIO_WritePin()函数将引脚拉低,延时一段时间后再将其释放。
3. 发送指令:为了读取温度数据,您需要发送一系列指令给传感器。具体指令可以在DS18B20的数据手册中找到。使用GPIO_WritePin()函数来发送指令。
4. 接收数据:传感器将以序列的形式回传温度数据。您需要使用GPIO_ReadPin()函数来读取数据线上的电平,并将其保存到缓冲区中。
5. 解析数据:根据DS18B20的协议,您可以解析缓冲区中的数据来获取实际的温度值。
请注意,以上仅为简要概述,实际操作可能会更加复杂。为了更好地理解和实施DS18B20传感器的使用,建议查阅STM32F1HAL库的文档以及DS18B20传感器的数据手册。
相关问题
ds18b20温度传感器stm32hal库
DS18B20温度传感器的STM32HAL库是一种软件例程源码,用于在STM32单片机上驱动DS18B20温度传感器。DS18B20是一种数字温度传感器,具有体积小、适用电压宽、经济等特点。它支持一线总线接口,是世界上第一片支持该接口的温度传感器。如果你需要更详细的信息,可以参考《嵌入式-STM32开发指南》第三部分外设篇-第2章温度传感器DS18B20这篇文章,其中有关于DS18B20的详细介绍。
ds18b20温度传感器stm32 hal库代码
以下是DS18B20温度传感器的STM32 HAL库代码示例:
```c
#include "stm32f4xx_hal.h"
#define DS18B20_PIN GPIO_PIN_0
#define DS18B20_PORT GPIOA
float ds18b20_read_temperature(void);
void ds18b20_reset(void);
void ds18b20_write_bit(uint8_t bit);
uint8_t ds18b20_read_bit(void);
void ds18b20_write_byte(uint8_t byte);
uint8_t ds18b20_read_byte(void);
void ds18b20_reset(void)
{
HAL_GPIO_WritePin(DS18B20_PORT, DS18B20_PIN, GPIO_PIN_RESET);
HAL_Delay(480);
HAL_GPIO_WritePin(DS18B20_PORT, DS18B20_PIN, GPIO_PIN_SET);
HAL_Delay(60);
while (!HAL_GPIO_ReadPin(DS18B20_PORT, DS18B20_PIN));
HAL_Delay(420);
}
void ds18b20_write_bit(uint8_t bit)
{
HAL_GPIO_WritePin(DS18B20_PORT, DS18B20_PIN, GPIO_PIN_RESET);
HAL_Delay(bit ? 6 : 60);
HAL_GPIO_WritePin(DS18B20_PORT, DS18B20_PIN, GPIO_PIN_SET);
HAL_Delay(bit ? 60 : 6);
}
uint8_t ds18b20_read_bit(void)
{
uint8_t bit = 0;
HAL_GPIO_WritePin(DS18B20_PORT, DS18B20_PIN, GPIO_PIN_RESET);
HAL_Delay(6);
HAL_GPIO_WritePin(DS18B20_PORT, DS18B20_PIN, GPIO_PIN_SET);
HAL_Delay(9);
bit = HAL_GPIO_ReadPin(DS18B20_PORT, DS18B20_PIN);
HAL_Delay(55);
return bit;
}
void ds18b20_write_byte(uint8_t byte)
{
for (int i = 0; i < 8; i++) {
ds18b20_write_bit(byte & (1 << i));
}
}
uint8_t ds18b20_read_byte(void)
{
uint8_t byte = 0;
for (int i = 0; i < 8; i++) {
byte |= ds18b20_read_bit() << i;
}
return byte;
}
float ds18b20_read_temperature(void)
{
ds18b20_reset();
ds18b20_write_byte(0xCC);
ds18b20_write_byte(0x44);
HAL_Delay(750);
ds18b20_reset();
ds18b20_write_byte(0xCC);
ds18b20_write_byte(0xBE);
uint16_t raw_temperature = ds18b20_read_byte() | (ds18b20_read_byte() << 8);
int8_t sign = (raw_temperature & 0x8000) ? -1 : 1;
raw_temperature = (raw_temperature >> 4) & 0x0FFF;
float temperature = (float) raw_temperature / 16.0f * sign;
return temperature;
}
int main(void)
{
HAL_Init();
__HAL_RCC_GPIOA_CLK_ENABLE();
GPIO_InitTypeDef GPIO_InitStruct;
GPIO_InitStruct.Pin = DS18B20_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(DS18B20_PORT, &GPIO_InitStruct);
float temperature = ds18b20_read_temperature();
// Do something with the temperature value
while (1);
}
```