在HAL库环境下使用串口2搭建ECB02串口透传,蓝牙端发送过来的数据转化为int型数据串口2接收,通过串口1打印串口2接收到的数据
时间: 2023-09-21 14:06:29 浏览: 65
### 回答1:
可以参考以下代码实现:
```c
#include "stm32f10x.h"
#include "stdio.h"
#define USART1_DR_Base 0x40013804
#define USART2_DR_Base 0x40004404
void USART1_Init(uint32_t baudrate) {
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 打开对应外设的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_USART1, ENABLE);
// 配置 USART1 Tx (PA9) 引脚为推挽输出模式
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置 USART1 Rx (PA10) 引脚为浮空输入模式
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置 USART1
USART_InitStructure.USART_BaudRate = baudrate;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 使能 USART1
USART_Cmd(USART1, ENABLE);
}
void USART2_Init(uint32_t baudrate) {
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 打开对应外设的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB1Periph_USART2, ENABLE);
// 配置 USART2 Tx (PA2) 引脚为推挽输出模式
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置 USART2 Rx (PA3) 引脚为浮空输入模式
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置 USART2
USART_InitStructure.USART_BaudRate = baudrate;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART2, &USART_InitStructure);
// 使能 USART2
USART_Cmd(USART2, ENABLE);
}
void USART1_SendChar(char ch) {
USART_SendData(USART1, (uint8_t)ch);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
}
void USART1_SendString(const char* str) {
while (*str) {
USART1_SendChar(*str++);
}
}
char USART2_RecvChar(void) {
while (USART_GetFlagStatus(USART2, USART_FLAG_RXNE) == RESET);
return (char)USART_ReceiveData(USART2);
}
void USART2_SendChar(char ch) {
USART_SendData(USART2, (uint8_t)ch);
while (USART_GetFlagStatus(USART2, USART_FLAG_TXE) == RESET);
}
void USART2_SendString(const char* str) {
while (*str) {
USART2_SendChar(*str++);
}
}
int main(void) {
int data;
USART1_Init(115200);
USART2_Init(9600);
while (1) {
// 从串口2接收数据
data = 0;
data |= USART2_RecvChar() << 24;
data |= USART2_RecvChar() << 16;
data |= USART2_RecvChar() << 8;
data |= USART2_RecvChar();
// 将数据通过串口1打印出来
char buf[50];
sprintf(buf, "Received data: %d\r\n", data);
USART1_SendString(buf);
}
}
```
在主函数的死循环中,我们通过 `USART2_RecvChar()` 函数从串口2接收数据,并将其转化为 int 型数据。然后,我们使用 `sprintf()` 函数将数据格式化为字符串,并通过 `USART1_SendString()` 函数将其打印到串口1上。需要注意的是,在使用 `USART2_RecvChar()` 函数接收数据时,为了保证数据的正确性,我们需要按照字节的顺序将数据组装起来,这里采用了大端字节序。
### 回答2:
在HAL库环境下,使用串口2搭建ECB02串口透传的过程如下:
1. 首先,需要在代码中包含正确的头文件和宏定义,如下:
```c
#include "stm32f4xx_hal.h"
#include "usart.h"
// 定义接收缓冲区大小
#define RX_BUFF_SIZE 10
// 定义接收缓冲区
uint8_t rxBuffer[RX_BUFF_SIZE];
```
2. 在主函数中,需要初始化串口1和串口2:
```c
int main()
{
// 初始化HAL库
HAL_Init();
// 初始化串口1和串口2
MX_USART1_UART_Init();
MX_USART2_UART_Init();
// 设置中断优先级
HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
// 启动UART2接收中断
HAL_UART_Receive_IT(&huart2, (uint8_t *)rxBuffer, RX_BUFF_SIZE);
// 进入主循环
while(1)
{
// 打印串口2接收到的数据
printf("Received data from UART2: %s\n", rxBuffer);
}
return 0;
}
```
3. 在串口2接收中断处理函数中,将接收到的数据转化为int型数据,并通过串口1打印出来:
```c
void USART2_IRQHandler(void)
{
HAL_UART_IRQHandler(&huart2);
}
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
{
if (huart->Instance == USART2)
{
// 将接收到的数据转化为int型数据
int data = atoi((char *)rxBuffer);
// 通过串口1打印串口2接收到的数据
printf("Data received from UART2: %d\n", data);
// 重新启动UART2接收中断
HAL_UART_Receive_IT(&huart2, (uint8_t *)rxBuffer, RX_BUFF_SIZE);
}
}
```
通过以上步骤,就可以在HAL库环境下使用串口2搭建ECB02串口透传,将蓝牙端发送过来的数据转化为int型数据,然后通过串口1打印串口2接收到的数据。确保正确初始化串口1和串口2,并启动UART2接收中断,以便实时接收数据。在串口2接收中断处理函数中,将接收到的数据转化为int型并打印出来,然后重新启动UART2接收中断以实现循环接收数据的功能。
### 回答3:
在HAL库环境下使用串口2搭建ECB02串口透传,蓝牙端发送过来的数据转化为int型数据串口2接收,通过串口1打印串口2接收到的数据的步骤如下:
1. 首先,你需要在STM32的工程中配置串口2作为透传通道的接收端口。打开STM32的串口2,并设置波特率、数据位、校验位和停止位等相关参数。
2. 创建一个接收缓冲区,用于存储串口2接收到的数据,并设置一个接收标志位。
3. 在主程序的循环中,检测串口2是否接收到数据。如果接收到数据,将接收到的数据存储到接收缓冲区中,并将接收标志位置为1。
4. 在串口1的中断服务程序(USART1_IRQHandler)中,检测串口2的接收标志位。如果接收标志位为1,将接收缓冲区中的数据转化为int型数据,并通过串口1将其打印出来。
5. 在蓝牙模块发送数据的代码中,将需要发送的int型数据转化为字符串,并通过串口2发送出去。
这样,当蓝牙端发送数据时,串口2会接收到对应的数据,并转化为int型数据。然后,通过串口1,你可以看到串口2接收到的int型数据。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)