keil5 rs485发送数据函数
时间: 2023-07-29 17:07:02 浏览: 63
下面是一个简单的 Keil5 RS485 发送数据函数的示例代码:
```
void RS485_SendData(uint8_t *data, uint16_t len)
{
// 切换到发送模式
GPIO_WritePin(RS485_DIR_PORT, RS485_DIR_PIN, GPIO_PIN_SET);
// 发送数据
for (uint16_t i = 0; i < len; i++) {
USART_SendData(USART1, data[i]);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
}
// 切换到接收模式
GPIO_WritePin(RS485_DIR_PORT, RS485_DIR_PIN, GPIO_PIN_RESET);
}
```
其中 `RS485_DIR_PORT` 和 `RS485_DIR_PIN` 是控制 RS485 芯片方向控制引脚的 GPIO 端口和引脚号。该函数将 `data` 数组中的数据通过 USART1 发送出去,并在发送完成后将方向控制引脚切换到接收模式。注意在发送数据前需要先将方向控制引脚切换到发送模式,发送完成后再切回接收模式,否则可能会出现数据冲突。
相关问题
keil5rs485发送数组
以下是在Keil 5中使用RS485发送数组的示例代码:
```c
#include<stm32f4xx.h>
#include<stdio.h>
#define RS485_UART USART3 //定义RS485所使用的USART
#define RS485_DIR_PIN GPIO_Pin_15 //定义RS485转换方向控制引脚
#define RS485_DIR_PORT GPIOA //定义RS485转换方向控制引脚所在的端口
void RS485_Init(void)
{
USART_InitTypeDef USART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE); //使能GPIOA时钟
//配置PA15为推挽输出引脚
GPIO_InitStructure.GPIO_Pin = RS485_DIR_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(RS485_DIR_PORT, &GPIO_InitStructure);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE); //使能USART3时钟
//USART3配置
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(RS485_UART, &USART_InitStructure);
USART_Cmd(RS485_UART, ENABLE); //使能USART3
}
void RS485_SendArray(u8 *data, u8 len)
{
GPIO_SetBits(RS485_DIR_PORT, RS485_DIR_PIN); //设置RS485为发送状态
for (u8 i = 0; i < len; i++)
{
USART_SendData(RS485_UART, data[i]); //向USART3发送数据
while (USART_GetFlagStatus(RS485_UART, USART_FLAG_TXE) == RESET); //等待发送完成
}
while (USART_GetFlagStatus(RS485_UART, USART_FLAG_TC) == RESET); //等待发送完成
GPIO_ResetBits(RS485_DIR_PORT, RS485_DIR_PIN); //设置RS485为接收状态
}
int main(void)
{
RS485_Init(); //初始化RS485
u8 data[] = {0x01, 0x02, 0x03, 0x04, 0x05}; //定义要发送的数组
RS485_SendArray(data, sizeof(data)); //发送数组数据
while (1);
}
```
在上述代码中,首先通过`RS485_Init()`函数初始化RS485的USART和控制引脚。然后,通过`RS485_SendArray()`函数发送数组数据。在发送数组数据之前,需要设置RS485为发送状态,发送完数据后,再将RS485设置为接收状态。
keil5STM32F103使用RS485发送接受函数
以下是使用Keil5和STM32F103来进行RS485发送接收的函数示例:
```
#include "stm32f10x.h"
#define RS485_DIR_GPIO GPIOB
#define RS485_DIR_PIN GPIO_Pin_12
void RS485_SendData(uint8_t *pData, uint16_t len)
{
// Set RS485 Direction to Transmit
GPIO_WriteBit(RS485_DIR_GPIO, RS485_DIR_PIN, Bit_RESET);
// Send data using UART
for (uint16_t i = 0; i < len; i++)
{
USART_SendData(USART1, pData[i]);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
}
// Wait for transmission complete
while (USART_GetFlagStatus(USART1, USART_FLAG_TC) == RESET);
// Set RS485 Direction to Receive
GPIO_WriteBit(RS485_DIR_GPIO, RS485_DIR_PIN, Bit_SET);
}
void RS485_ReceiveData(uint8_t *pData, uint16_t len)
{
// Set RS485 Direction to Receive
GPIO_WriteBit(RS485_DIR_GPIO, RS485_DIR_PIN, Bit_SET);
// Receive data using UART
for (uint16_t i = 0; i < len; i++)
{
while (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET);
pData[i] = USART_ReceiveData(USART1);
}
}
```
在这个例子中,我们使用USART1来进行串口通信,同时使用一个GPIO引脚(PB12)来控制RS485芯片的发送/接收方向。在发送数据时,我们将RS485引脚设置为发送状态,然后使用USART1发送数据。在接收数据时,我们将RS485引脚设置为接收状态,然后使用USART1接收数据。需要注意的是,在接收数据时,为了防止丢失任何数据,我们必须等待USART_FLAG_RXNE标志位被设置为1,表示接收缓冲区中有可用的数据。
请注意,此代码仅用于参考,具体实现可能因应用程序而异。