I2C1的clockspeed是什么,值可以是什么
时间: 2023-12-24 17:53:47 浏览: 26
I2C1的clock speed是指I2C总线传输数据时的时钟频率。在STM32系列微控制器中,I2C1的clock speed可以设置为100kHz或400kHz。
可以使用以下代码将I2C1的clock speed设置为100kHz:
```
// 设置I2C1的时钟频率为100kHz
I2C1_InitStruct.ClockSpeed = 100000;
```
或者将I2C1的clock speed设置为400kHz:
```
// 设置I2C1的时钟频率为400kHz
I2C1_InitStruct.ClockSpeed = 400000;
```
需要注意的是,I2C总线的时钟频率不能超过设备支持的最大频率。在设置I2C时钟频率时,需要根据具体的设备手册来确定最大支持的频率。
相关问题
设置I2C1波特率控制
在STM32中,可以通过以下步骤设置I2C1波特率控制:
1. 配置I2C1引脚。在GPIO初始化中配置I2C1的SCL和SDA引脚为复用模式,并设置为开漏输出(ODR高电平时为高阻态)。
2. 初始化I2C1。通过I2C_Init函数初始化I2C1的时钟速率、I2C模式等参数。其中,时钟速率的计算公式为:
I2C_Speed = APB1时钟频率 / (I2C时钟周期 * 2)
其中,I2C时钟周期的取值范围为0到15,可以通过I2C_ClockSpeed_TypeDef枚举类型进行设置。
3. 设置I2C1的CCR寄存器。在I2C初始化之后,可以通过I2C_CalculatePEC函数计算实际的I2C时钟速率和CCR寄存器的值。然后,通过I2C_SetCCR函数设置I2C1的CCR寄存器。
下面是一个示例代码片段:
```
GPIO_InitTypeDef GPIO_InitStructure;
I2C_InitTypeDef I2C_InitStructure;
// 配置I2C1引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructure);
// 初始化I2C1
I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;
I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2;
I2C_InitStructure.I2C_OwnAddress1 = 0x00;
I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;
I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
I2C_InitStructure.I2C_ClockSpeed = 100000; // 100KHz
I2C_Init(I2C1, &I2C_InitStructure);
// 设置I2C1的CCR寄存器
uint32_t I2C_Speed = 0;
uint16_t I2C_CCR = 0;
I2C_CalculatePEC(I2C1, 100000, &I2C_Speed, &I2C_CCR);
I2C_SetCCR(I2C1, I2C_CCR);
```
I2C_InitTypeDef I2C_InitStruct; I2C_InitStruct.I2C_Mode = I2C_Mode_I2C; I2C_InitStruct.I2C_DutyCycle = I2C_DutyCycle_2; I2C_InitStruct.I2C_OwnAddress1 = 0x00; I2C_InitStruct.I2C_Ack = I2C_Ack_Enable; I2C_InitStruct.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit; I2C_InitStruct.I2C_ClockSpeed = 100000; I2C_Init(I2C1, &I2C_InitStruct);请将以上代码修改成直接操作寄存器
&I2C_InitStruct);
This code initializes the I2C peripheral with the following parameters:
- I2C_Mode_I2C: Sets the I2C peripheral to operate in I2C mode.
- I2C_DutyCycle_2: Sets the duty cycle to 2, which means that the data is sampled at the middle of the data bit period.
- I2C_OwnAddress1: Sets the own address of the I2C peripheral to 0x00.
- I2C_Ack_Enable: Enables the acknowledgement of received data.
- I2C_AcknowledgedAddress_7bit: Sets the address size of the I2C peripheral to 7 bits.
- I2C_ClockSpeed: Sets the clock speed of the I2C peripheral to 100kHz.
The I2C_Init() function then initializes the I2C peripheral with the specified parameters. This code is specific to the STM32 microcontroller family and may differ for other microcontrollers.
相关推荐
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://img-home.csdnimg.cn/images/20210720083646.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)