基于DE2-115平台VGA显示图片详细步骤
时间: 2023-08-02 07:18:52 浏览: 65
好的,以下是基于DE2-115平台VGA显示图片的详细步骤:
1. 打开Quartus II软件,创建一个新工程。
2. 在工程中添加一个VHDL文件,用于实现VGA控制器。下面是一个简单的VGA控制器代码示例:
```
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
entity VGA_Controller is
Port ( clk : in STD_LOGIC;
h_sync : out STD_LOGIC;
v_sync : out STD_LOGIC;
red : out STD_LOGIC_VECTOR (3 downto 0);
green : out STD_LOGIC_VECTOR (3 downto 0);
blue : out STD_LOGIC_VECTOR (3 downto 0);
x : out STD_LOGIC_VECTOR (9 downto 0);
y : out STD_LOGIC_VECTOR (9 downto 0));
end VGA_Controller;
architecture Behavioral of VGA_Controller is
signal vga_clk : std_logic;
signal h_count : integer range 0 to 799 := 0;
signal v_count : integer range 0 to 524 := 0;
begin
vga_clk <= clk;
process(vga_clk) begin
if rising_edge(vga_clk) then
if h_count = 799 then
h_count <= 0;
if v_count = 524 then
v_count <= 0;
else
v_count <= v_count + 1;
end if;
else
h_count <= h_count + 1;
end if;
end if;
end process;
h_sync <= '1' when (h_count >= 656 and h_count <= 752) else '0';
v_sync <= '1' when (v_count >= 490 and v_count <= 492) else '0';
red <= "1111";
green <= "0000";
blue <= "0000";
x <= std_logic_vector(to_unsigned(h_count, 10));
y <= std_logic_vector(to_unsigned(v_count, 10));
end Behavioral;
```
这个VGA控制器代码示例中,使用了默认的640x480分辨率和60Hz刷新率。其中,h_sync和v_sync分别表示水平同步信号和垂直同步信号,red、green和blue分别表示红、绿、蓝三个颜色通道,x和y表示当前像素的坐标。
3. 在工程中添加一个图片文件,将其转换为灰度图像并调整分辨率为640x480。可以使用Matlab等工具进行图像处理和转换。
4. 在VGA控制器代码中添加一个ROM模块,用于存储转换后的图像数据。下面是一个简单的ROM模块代码示例:
```
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.NUMERIC_STD.ALL;
entity ROM is
Port ( clk : in STD_LOGIC;
address : in STD_LOGIC_VECTOR (17 downto 0);
data : out STD_LOGIC_VECTOR (7 downto 0));
end ROM;
architecture Behavioral of ROM is
type ROM_array is array (0 to 307199) of std_logic_vector(7 downto 0);
constant ROM_data : ROM_array := (
-- 图像数据
);
begin
process(clk) begin
if rising_edge(clk) then
data <= ROM_data(to_integer(unsigned(address)));
end if;
end process;
end Behavioral;
```
在ROM模块中,使用一个ROM_array类型的常量存储转换后的图像数据,通过address输入读取对应的像素数据。
5. 在VGA控制器代码中,将ROM模块的输出与红、绿、蓝三个颜色通道连接起来,实现将像素数据输出到VGA显示器。
6. 在Quartus II软件中,进行引脚分配,将VGA控制器的输出信号与DE2-115板子上的VGA接口相连。
7. 编译工程生成.sof文件,并将其下载到DE2-115板子中。
完成以上步骤后,即可在DE2-115的VGA显示器上看到输出的图像。需要注意的是,因为DE2-115的FPGA资源有限,可能无法一次性显示完整的640x480分辨率的图像。可以将图像分成若干个区域分别输出,或者降低分辨率以适应FPGA资源。