Arduino 750baud
时间: 2023-10-08 08:13:39 浏览: 46
Arduino支持的串口通信波特率有很多种,如9600、115200等。如果要使用750baud的波特率,可以使用Arduino的SoftwareSerial库,自定义一个Serial对象,然后设置该对象的波特率为750,示例代码如下:
```C++
#include <SoftwareSerial.h>
SoftwareSerial mySerial(10, 11); // RX, TX
void setup() {
Serial.begin(9600);
mySerial.begin(750);
}
void loop() {
if (mySerial.available()) {
Serial.write(mySerial.read());
}
if (Serial.available()) {
mySerial.write(Serial.read());
}
}
```
其中,10和11分别是Arduino的数字引脚,用于作为软串口的RX和TX引脚。在setup函数中,分别初始化了硬串口和软串口,并设置软串口的波特率为750。在loop函数中,通过判断软串口和硬串口是否有数据可读,实现了软串口和硬串口之间的数据传输。
相关问题
Baud-search
烧录Arduino时出现"programmer is not responding"的错误可能是因为串口波特率设置不正确(baud rate),或者硬件连接有问题[^1]。通常情况下,你需要确认几个步骤来解决此问题:
1. 确保arduino的串口(COM5或相应端口)已正确打开并且与正确的编程器相连。如果设备连接有问题,尝试换一个USB端口试试。
2. 校准BAUD速率。`avrdude`默认使用的可能是不同项目所需的速率。确保你配置的baud rate与硬件手册或你正在使用的Arduino board型号所推荐的一致。如果不确定,通常Arduino Uno的串口速率为115200,但请检查项目文档或主板说明书来核实正确设置。
假设你想要手动检查并设置波特率:
```sh
nano ~/arduinosketch/tools/platforms/arduino/hardware/avr/variants/standard/avrdude.conf // 用文本编辑器打开该文件
```
找到 `port /dev/ttyACMx` 这样的行,替换`x`为实际的端口号,如`ttyACM0` 或 `COM5`,并确保`baudRate`设置正确。
完成后重启你的arduino,重新进行烧录尝试。如果你还是遇到相同问题,请更新你的硬件或查找特定芯片或板子的支持文档。记得在提供的资源中找到合适的LGT8FX包,以便进行特定设备上的程序烧录。
arduino mega2560 uart
Arduino Mega2560 has a total of four hardware UART (Universal Asynchronous Receiver-Transmitter) interfaces. These interfaces are labeled as Serial, Serial1, Serial2, and Serial3. The main Serial interface is connected to the USB-to-Serial converter and is commonly used for serial communication with the computer.
To use the UART interfaces on the Arduino Mega2560, you can use the Serial library in your Arduino sketch. Here's an example of how to use Serial1 for communication:
```cpp
void setup() {
// Set the baud rate for Serial1
Serial1.begin(9600);
}
void loop() {
// Read data from Serial1
if (Serial1.available()) {
char data = Serial1.read();
// Do something with the received data
}
// Send data through Serial1
Serial1.print("Hello, world!");
delay(1000);
}
```
In this example, we initialize Serial1 with a baud rate of 9600 in the `setup()` function. In the `loop()` function, we check if there is any data available to read from Serial1 using the `available()` function. If there is data available, we read it using the `read()` function. We can also send data through Serial1 using the `print()` function.
You can use the same approach to communicate with other UART interfaces on the Arduino Mega2560 by replacing `Serial1` with `Serial2` or `Serial3` in your code.
相关推荐
![doc](https://img-home.csdnimg.cn/images/20210720083327.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)