两个arduino uno通信代码
时间: 2023-10-08 19:14:50 浏览: 136
以下是两个Arduino Uno之间通过串口通信的示例代码:
发送端(Arduino Uno #1)代码:
```C++
void setup() {
Serial.begin(9600); // 设置串口通信波特率为9600
}
void loop() {
String msg = "Hello, Arduino Uno #2!"; // 要发送的消息
Serial.println(msg); // 发送消息
delay(1000); // 等待1秒
}
```
接收端(Arduino Uno #2)代码:
```C++
void setup() {
Serial.begin(9600); // 设置串口通信波特率为9600
}
void loop() {
if (Serial.available() > 0) { // 如果有可读取的消息
String msg = Serial.readString(); // 读取消息
Serial.println("Received message: " + msg); // 打印接收到的消息
}
}
```
请注意,这里的串口通信波特率必须在发送端和接收端之间相同,否则它们将无法正确地通信。在示例代码中,我们将波特率设置为9600。
相关问题
两块arduino uno板串口通信
要实现两块Arduino Uno板之间的串口通信,需要在每个板子上分别编写代码。以下是一个简单的示例:
在发送方Arduino Uno上,您可以编写以下代码:
```c++
void setup() {
Serial.begin(9600); // 初始化串口通信,波特率为9600
}
void loop() {
Serial.println("Hello World!"); // 向接收方发送消息
delay(1000); // 延迟1秒
}
```
在接收方Arduino Uno上,您可以编写以下代码:
```c++
void setup() {
Serial.begin(9600); // 初始化串口通信,波特率为9600
}
void loop() {
if (Serial.available() > 0) { // 如果有数据可用
String message = Serial.readString(); // 读取串口数据
Serial.println(message); // 输出接收到的消息
}
}
```
在这个示例中,发送方向接收方发送“Hello World!”消息,并每隔1秒重复发送。接收方通过检查串口数据是否可用来接收消息,并在接收到消息时将其打印出来。
请注意,两个板子的串口通信需要连接它们的TX和RX引脚。因为两个板子都有一个硬件串口,所以需要将其中一个板子的TX引脚连接到另一个板子的RX引脚,同时需要将另一个板子的TX引脚连接到第一个板子的RX引脚。例如,将一个Arduino Uno的TX引脚连接到另一个Arduino Uno的RX引脚,并将另一个Arduino Uno的TX引脚连接到第一个Arduino Uno的RX引脚。
esp32cam与arduino uno通信
要让ESP32-CAM与Arduino Uno通信,可以使用串行通信(Serial Communication)或者I2C通信(Inter-Integrated Circuit Communication)。
对于串行通信,需要将ESP32-CAM和Arduino Uno分别连接到电脑上,并利用Arduino IDE打开两个串口监视器(Serial Monitor)。然后,在ESP32-CAM上运行一个程序,将需要传输的数据通过串口发送给Arduino Uno。同时,在Arduino Uno上编写一个程序,接收ESP32-CAM发送过来的数据并进行处理。
对于I2C通信,需要将ESP32-CAM和Arduino Uno分别连接到同一个电路板上,并通过I2C总线相连接。在ESP32-CAM上运行一个程序,将需要传输的数据通过I2C发送给Arduino Uno。同时,在Arduino Uno上编写一个程序,接收ESP32-CAM发送过来的数据并进行处理。
无论采用哪种通信方式,具体的实现方式可以参照相关的资料和示例代码进行操作。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)